Вытяжки ELICA ADAGIO GME BL/A/90 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
16
reduces the suction effectiveness equivalent to 1 linear
metre. (E.g.: if two 90° curves are used, the duct should
be no longer than 3 metres).
•
Avoid drastic changes of direction.
•
Use a duct with 150mm diameter constant for the whole
length.
•
Use a duct made of standard complying material.
•
Remove the safety shim highlighted in the picture (
Fig. 1-
2
) at the end of the installation.
•
In case of failure to observe the instructions above, the
supplier can not be held responsible for capacity or noise
problems and no warranty will be granted.
•
Before making the hole, make sure that the inside of the
cabinet, near the hood housing area, does not have the
structure of the cabinet or other particulars which may
cause problems for the proper installation. Make sure
that the overall dimensions of the hood and the hob ae
compatible with the cabinet and therefore the installation
is feasible.
•
Perform, in the back of the hob, a rectangular hole with
the following dimensions:
(Fig. 20)
Hood 60cm Model:
542x100mm.
Hood 90cm Model:
842x100mm.
Hood 120cm Model:
1142x100mm
•
Install the hood in the hole made, inserting it from above,
as shown (
Fig. 3
). In case of version with motor on
board, it is necessary to remove the suction unit before
inserting the product into the cabinet.
•
Fix the hood inside the cainet using the special brackets
supplied (
Fig. 4
). Start mounting the brackets in the lower
part of the hood (
Fig. 5a
) making sure that there is a
distance of 2 mm between the lower part of the bracket
and the cabinet bottom (
Fig. 5b
). This distance allows
the traction of the product downwards on fixing, (
Fig. 5c
),
so that the stainless steel frame adheres perfectly on the
worktop.
•
Before inserting the screws into the cabinet, make sure
that the product is perfectly perpendicular to the worktop.
• After completing the installation and connecting the
product to the power supply, lift the hood and remove the
door lock (
Fig. 6
).
•
In case of version with motor on board start mounting the
motor unit directing the air outlet to the chosen position
downwards or upwards (
Fig. 7b
). The motor can be
installed on both the front side and the back one of the
hood. Once the installationof the motor has been
comleted, start mounting the duct for the air outlet.
•
In case of version with external motor put the suction unit
(external motor) in a suitable area and arrange the air
outlet duct. Start mounting the air outlet duct between the
external motor and the hood. Select the air outlet among
the five possibilities (
Fig. 7a
) and install the union
supplied.
•
Put the metal box containing the electronic components
in an easily accessible area for any assistance
operations (
Fig. 8
), connecting the electric connectors of
the same to the hood: pushbutton panel connector (
Fig.
9a
), 9-pole connector (
Fig. 9b
), neon connector (
Fig. 9c
)
• In case of installation with remote motor,connect the
power unit cable to the special connector placed on the
electronic components box (
Fig.10a
)
•
Connect the product to the power supply
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)
