ProfiCare PC-PW 3007 FA 8 в 1 Weiss - Инструкция по эксплуатации - Страница 37

37

PC-PW3007FA_IM 

13.10.17

The signal is generally safe! However, please read our spe-

cial safety instructions!
The method of measurement is referred to as “bioelectric 

impedance analysis” (BIA), a factor which is based on the 

relationship between body weight and associated body water 

percentages as well as on other biological data (age, gender, 

body weight).

Use

  NOTE:

•  The buttons are sensor touch buttons. Touch the but-

tons lightly with a finger to execute the function.

•  The scales are factory set with the units “kg” and “cm”.

To change the settings to “lb” or “st:lb” as well as “ft:in”, 

proceed as follows:
1.  Turn on the scales by light pressure with the foot onto the 

weighing surface.

2.  Press the   or   button repeatedly until the desired 

weight unit is displayed. The unit for the height also auto-

matically changes.

Weighing Function
1.  Place the scale on a hard, flat surface (avoid carpets). An 

uneven floor contributes to inaccurate measurements.

2.  Stand on the scales with both feet. The appliance 

switches on automatically.

3.  Distribute your weight equally and wait for the scale to 

determine your weight.

4.  The digits on the display will flash before your exact 

weight will be shown.

•  In order to extend the battery life, the appliance will 

automatically turn off 15 seconds after you have stepped 

off the scale.

•  If there is no weight determination while “0.0” is shown, 

the scale will shut off automatically after 15 seconds.

Saving Personal Data

  NOTE:

•  The scale has default values that you can change, as 

described below.

•  Carry out the following steps in sequence and within a 

few seconds. Otherwise, the appliance will automati-

cally cancel input mode.

•  Holding one of the buttons (   /   ) pressed for approx. 

2 seconds selects fast mode.

1.  Press the button  . The memory location selected last 

flashes on the display (for example P0). Confirm the 

setting by pressing   or select another memory space 

by pressing the   /   button. Then press   to go to the 

next setting.

2.  The symbol for “male” or “female” will flash. Confirm the 

setting by pressing   or use the   /   button to choose 

the symbol for your gender. Then press   to go to the 

next setting.

3.  The height setting will flash. Select your height by press-

ing   or   button. Confirm your entry by pressing  .

4.  The setting age will flash. Select your age by pressing  

 or   button. Confirm your entry by pressing  .

5.  The short display “ 

 ” will terminate the entry mode 

for this memory location. Then you will see the memory 

location, the symbol of the gender and the weight “0.0 kg” 

(0.0 lb / 0: 00 st:lb) in the display.

You now have the following options:
•  Press the   button repeatedly to display the settings 

again or to change them.

•  You can set further preset locations. Proceed as de-

scribed above.

•  You can immediately start measuring.

Measurement and Analysis
Record your personal data in the memory.

  NOTE:

•  The analysis scale will only work correctly when you 

are standing on the contact surfaces barefoot and with 

slightly moistened foot soles, if possible. Completely 

dry foot soles can lead to unsatisfactory results as they 

have a conductivity that is too low. 

•  If necessary wipe the contact surfaces to improve 

results.

•  Due to the significant fluctuation of body fat, it is difficult 

to attain a standard value. Therefore, to obtain consist-

ent data, always measure at the same time of day.

•  Amongst other things, our body consists of body 

fat, body water, muscle mass and bone weight. The 

obtained values may differ due to individual water reten-

tion within these main components. This is normal and 

highly dependent on nutrition and lifestyle.

1.  Press the   button. Use the   /   button to select the 

stored position at which your data is saved. The location 

flashes for approx. 3 seconds. Then you will see the 

memory location, the symbol of the gender and the weight 

“0.0 kg” (0.0 lb / 0: 00 st:lb) in the display.

2.  Stand on the contact surfaces (5) of the scales with both 

feet.

3.  Firstly your weight will flash on the display. The analysis 

starts after the display has stopped flashing. You’ll see 

a treadmill “ 

 ” in the display during the analysis. 

Remain on the scales until the last display (   ) has 

appeared.
The following results are displayed one after the other:

1.  The weight in the previously selected unit (kg / lb / st:lb)

2.  The body fat proportion in % (fat)

3.  The proportion of body fluid % (TBW)

4.  The proportion of muscle mass in % (   )

5.  The bone weight in kg (   )