MBS PG-904 - Инструкция по эксплуатации - Страница 22

8

8

SETTINGS FOR OTHER GAS TYPES

If another gas type other than the ones specified on the equipment label will be used, injectors 
shall be changed. If spare injector has not been given together with the equipment, then it 
may be provided from the authorized services.

In order to identify the injector type that must be used, please refer to the injector table. 
Injectors are identified with 100s of mm's according to their diameters and this data is printed on 
the injector.

Changing the injectors

·   

Uninstall the grill and the burner caps.

·

By using a wrench, replace injector "J" with the a typ suitable for the gas type.

·

Replace the burners back into their positions.

·

It is not necessary to make air adjustment for the burners.

Adjustment of minimum flame position

After you change the injectors, ignite the burner and take out the control switch. Turn the gas valve 
to its minimum position, insert a screwdriver into the knob and screw down to decrease the flame 
and screw up to increase the flame (figure 18).

Screw down the screw completely for (LPG) G30 type gases

Flame shall be small and uniform around the burner's ring.
At last, make sure that flame does not go out when the gas valve is turned instantly from 
maximum flame position to minimum position. Remember that flame shall be in contact gently 
for the cookers with a security valve. In order to make sure that settings are correct, leave the 
burners blazing for 5 minutes. If the flame dies out, increase the minimum flma setting.

CLEANING THE COOKER

In order to maintain your cooker in its best condition, wait for the cooker to cool down after each 
use and clean it regularly.

Never uninstall the control switches during cleaning.

Enamel parts

All enamel parts shall be cleaned with a soap  water solution or other suitable detergents by using 
a sponge. Cooker shall be dried out thoroughly after cleaning.

Stainless Steel Surfaces

Stainless steel surfaces shall be cleaned with a cleaning cloth and special agents used for 
cleaning of steel. After cleaning, stainless steel surfaces shall be wiped out preferably with a soft 
wash leather.

Grill

Enamel grills canbe washed in a washing machine.

Burner

Burners which are composed of two parts can be used by using an appropriate detergent. 
After cleaning, burners shall be thorougly dried out and they shall be placed into their original 
positions carefully.
For models with electronic ignition, keep electrode "E" clean at all times.
For models with security valve, clean valve "T" in order for it to continue its operation without 
any problems.
After the operation is completed, burners shall be placed into their original positions correctly.
In order not to damage the electronic ignition system, ignition system shall not be used when 
burners are not in their original places.

Electrical Compartments

Electrical compartments shall be cleaned while they are warm. Use a moist cloth for cleaning. 
Complete the cleaning operation by using mineral oil.

SETTINGS FOR OTHER GAS TYPES

Changing the injectors

It is not necessary to make air adjustment for the burners.

Adjustment of minimum flame position

Screw down the screw completely for (LPG) G30 type gases

CLEANING THE COOKER

Never uninstall the control switches during cleaning.

Enamel parts

Stainless Steel Surfaces

Grill

Burner

Electrical Compartments

If another gas type other than the ones specified on the equipment label will be used, injectors 
shall be changed. If spare injector has not been given together with the equipment, then it 
may be provided from the authorized services.

In order to identify the injector type that must be used, please refer to the injector table. 
Injectors are identified with 100s of mm's according to their diameters and this data is printed on 
the injector.

Uninstall the grill and the burner caps.

By using a wrench, replace injector "J" with the a typ suitable for the gas type.
Replace the burners back into their positions.

After you change the injectors, ignite the burner and take out the control switch. Turn the gas valve 
to its minimum position, insert a screwdriver into the knob and screw down to decrease the flame 
and screw up to increase the flame (figure 18).

Flame shall be small and uniform around the burner's ring.
At last, make sure that flame does not go out when the gas valve is turned instantly from 
maximum flame position to minimum position. Remember that flame shall be in contact gently 
for the cookers with a security valve. In order to make sure that settings are correct, leave the 
burners blazing for 5 minutes. If the flame dies out, increase the minimum flma setting.

In order to maintain your cooker in its best condition, wait for the cooker to cool down after each 
use and clean it regularly.

All enamel parts shall be cleaned with a soap  water solution or other suitable detergents by using 
a sponge. Cooker shall be dried out thoroughly after cleaning.

Stainless steel surfaces shall be cleaned with a cleaning cloth and special agents used for 
cleaning of steel. After cleaning, stainless steel surfaces shall be wiped out preferably with a soft 
wash leather.

Enamel grills canbe washed in a washing machine.

Burners which are composed of two parts can be used by using an appropriate detergent. 
After cleaning, burners shall be thorougly dried out and they shall be placed into their original 
positions carefully.
For models with electronic ignition, keep electrode "E" clean at all times.
For models with security valve, clean valve "T" in order for it to continue its operation without 
any problems.
After the operation is completed, burners shall be placed into their original positions correctly.
In order not to damage the electronic ignition system, ignition system shall not be used when 
burners are not in their original places.

Electrical compartments shall be cleaned while they are warm. Use a moist cloth for cleaning. 
Complete the cleaning operation by using mineral oil.

·   
·
·
·