Timberk THU UL 28 E - Инструкция по эксплуатации - Страница 7

www.timberk.com • electric humidifier

7

8. CLEANING AND MAINTENANCE

Before cleaning the device make sure that the plug is disconnected from 

the wall outlet. Otherwise, it may result in electric shock.

Before cleaning, wait until the cooling water in the ground, so as not to 

burn your hands. Spend device cleaning once or twice a week.
To clean the outer surface of the unit with a damp soft cloth.

To avoid electric shock, do not scratch or damage the device while 

cleaning elements.
Do not use when cleaning the device thinner, benzene, dimethyl benzene, 

stiff brush, talcum powder and other materials, except water.

Wipe any remaining water inside the base with a damp, soft cloth.

To remove the remaining water in the small details, you can use a soft 

brush, then wipe it again with a soft cloth.

In the formation of dirt on the membrane, clean it with a soft brushes. Use 

a soft brush to erase the remnants of water on the surface of the device, 

and then wipe it again with a soft cloth.
Rinse water tank and a clean water dispenser.

After removal of the residual water from the surface of the sprayer, wipe it 

with a soft cloth. Clean the outside surface with a damp, soft cloth.

IMPORTANT! 

To avoid deformation or wear of working surfaces, 

resulting in decreased atomizing or other malfunctions, 

do not use metallic brushes, blades or talc powder 

to wipe the atomizer’s surface. The water tank may 

leak upon heavy impacts. In case of water leakage, 

immediately stop using the unit and contact a service 

center. To keep the unit dry, remove water after cleaning 

and make sure to dry the unit’s case. Make sure that 

there is no water left inside the unit’s case. Prior to a 

long break in using the unit, dry its surface and pack it 

into a plastic bag, then put it into a box. Store the unit in 

a low-humidity room. Storing the unit undried results in 

generation of mold

In case of emergencies use troubleshooting methods, listed in Table 2. 

If it is impossible to remedy problems by the listed methods, contact the 

manufacturer’s service center.

9. TROUBLESHOOTING

Table 2

Problem

Possible cause

Remedy

Poor atomizing (insufficient 
capacity)

The unit is operating in the minimized 
mode (low atomizing frequency)

There is no problem. If you need to switch 
to the intensive mode of operation, turn the 
regulator handle all the way to the right.

The atomizer is clogged

Clean the atomizer.

Temperature of water in the tank is too low

Set maximum capacity. The humidifier’s 
capacity will go up after a while.

No atomizing

The power cord is poorly connected 
to the outlet

Connect the power cord into the outlet 
carefully

There is white deposit on objects 
around the humidifier (salts, 
separating out from water)

1. Lime deposits have formed on the 
membrane
2. There is a lot of salts in the water used 
(calcium and magnesium)

1. Clean the humidifier’s membrane with a 
special brush
2. Use filtered water

Steam has an unpleasant odor

Stale water is used

Clean the unit according to the cleaning 
and servicing instructions and fill the tank 
with fresh water

Remains of stale water or waste have 
accumulated in the unit’s case or the 
atomizer

Condensate is formed on the 
upper part of the humidifier and 
on surrounding objects, when it is 
operating.

1. High humidification intensity is set.
2. High room humidity and temperature.

Lower the humidification intensity by 
turning the on/off and steam outflow 
intensity regulator counterclockwise.

Water appears next to the humidifier, 
when it is operating.

1. High humidification intensity is set.
2. Lime deposits have formed on the 
membrane and in grooves for water (in 
the unit’s base).

1. Lower the humidification intensity by 
turning the on/off and steam outflow 
intensity regulator counterclockwise.
2. Clean the unit according to the cleaning 
and servicing instructions.

Water appears next to the humidifier, 
when it is not operating

Water tank is leaking

You need to contact an authorized service 
center