VITEK VT-1228 B - Инструкция по эксплуатации - Страница 5

5

              ENGLISH         

est and gradually raise it until you get the 
desired result).

•  Corduroy and other fabrics that start glossy 

quickly should be ironed strictly in one di-
rection (along the pile) with slight pressure.

•  To avoid appearance of glossy spots on the 

synthetic and silk fabrics, iron them back-
side.

SETTING THE IRONING TEMPERATURE

•  Lift the handle (1) and it will lock, to lower 

the handle (1) press the (7) button and low-
er the handle 

• Before connecting the iron to the electric 

network set the power supply switch (8) 
in correspondence with the voltage of the 
electric network. After usage of the iron with 
network voltage 110 V always set the switch 
(8) to the 220 V position, it will prevent mal-
function of the iron while connecting the iron 
to the electric network with the increased 
voltage.

•  Unwind the power cord and insert the plug 

into the socket.

•  Set the temperature control (11) to the re-

quired ironing temperature: “

•

”, “

••

”, 

“

•••

”, “max” depending on the type of fab-

ric, the (10) indicator will light up.

•  Place the iron vertically.
•  When the sole temperature (9) reaches the 

desired temperature value, the (10) indica-
tor will go out, you can start ironing.

  Note: When using the unit for the first 

time, the heating element of the unit 
burns that is why some smoke or foreign 
odor can appear.  It is normal.

IRONING WITHOUT STEAM

•  Set the constant steam supply on/off han-

dle (12) to the “ ” (steam supply is off).

•  Set the temperature control (11) to the re-

quired ironing temperature.

•  Place the iron vertically.
•  When the sole temperature (9) reaches the 

desired temperature value, the (7) indicator 
will go out, you can start ironing.

• After operation, take the plug out of the 

socket and wait until the iron cools down 
completely.

•  Press the (7) button and lower the iron han-

dle (4) down.

STEAM IRONING

While steam ironing set the temperature con-
trol (11) to the “max” position.
•  Fill the water tank with water as described in 

the corresponding section.

•  Insert the power plug into the socket.
•  Set the temperature control (11) to the “max” 

position, the indicator (10) will light up. 

•  Place the iron vertically.
•  When the sole temperature (9) reaches the 

desired temperature value, the (10) indica-
tor will go out, you can start ironing.

•  Switch on constant steam supply, by setting 

the handle (12) to the left position (steam 
supply is on); steam will be outgoing from 
the openings of the iron sole (9).

•  Set the temperature control (11) to the “min” 

position and the constant steam supply han-
dle (12) to the “ ” position (steam supply is 
off).

•  Take the plug out of the socket and wait until 

the iron cools down completely.

•  Open the lid (3) and pour out water from the 

tank.

• Press the button (7) and lower the handle 

(1) down.

ATTENTION! 

If during the operation steam 

is not constantly supplied, check whether the 
temperature control (11) is set properly, check 
the handle (12) position and whether there is 
water in the water tank (4).

ADDITIONAL STEAM RELEASE

Additional steam release function is useful 
when ironing folds and can only be used at 
high ironing temperatures (when the iron tem-
perature control (11) is set to “max”).
When the additional steam release button (2) 
is pressed, steam will be vigorously released 
from the openings in the iron sole.

Note: 
-  In order to avoid leakage of water from 

steam openings, press the additional 
steam supply button (2) with a 10-15 
sec. interval.

1228.indd   5

1228.indd   5

29.03.2011   12:57:21

29.03.2011   12:57:21