SKIL F0150735RA - Инструкция по эксплуатации - Страница 7

7

•  Always ensure that the ventilation openings are kept clear 

of debris

AFTER USE

•  Always switch off tool and disconnect plug from 

power source before making adjustments, changing 

spools, cleaning or leaving the tool unattended for 

any period

•  Store the tool 

indoors

 in a dry and locked-up place, out 

of reach of children

EXPLANATION OF SYMBOLS ON TOOL

3

 Warning

! Read the instruction manual

4

 Do not expose tool to rain

5

 Wear protective glasses

6

Pay attention to the risk of injury caused by flying 

debris

 (keep bystanders a safe distance away from work 

area)

7

 Immediately disconnect the plug if the (extension) cord is 

damaged or cut through while working

8

 Double insulation (no earth wire required)

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

•  If for any reason the old plug is cut of the cord of this tool, 

it must be disposed of safely and not left unattended

•  Do not connect the blue (= neutral) or brown (= live) wire 

in the cord of this tool to the earth terminal of the plug

USE

•  Cutting guard 

0

-  mount cutting guard A as illustrated with round head 

screw supplied

!  never use the tool without cutting guard A

•  Cord restraint 

!

-  hook the loop in the extension cord over restraint B as 

illustrated

-  pull tight to secure the extension cord

•  On/of 

@

-  switch on tool by pressing trigger switch C

-  switch of tool by releasing trigger switch C

!  after switching off the tool the cutting lines 

continue to rotate for a few seconds

-  allow the cutting lines to stop rotating before switching 

on again

!  do not rapidly switch on and off

•  Trimming

!  ensure that the red cover D 

2

 is removed from 

the line cutting blade before using the tool

!  ensure that the cutting area is free of stones, 

debris and other foreign objects

!  start trimming only when tool runs at full speed

-  start trimming near the mains socket and move away 

while working

-  cut long grass in layers (always start from the top)

-  only trim with the tip of the cutting line

-  do not cut damp or wet grass

-  prevent the cut grass from clogging the spool (do not 

make heavy cuts)

-  do not overload the tool

-  carefully cut around trees and bushes, so that they do 

not come into contact with the cutting lines

-  keep the tool away from solid objects in order to 

protect the cutting lines against excessive wear

-  be aware of the kickback forces that occur when solid 

objects are touched

•  Holding and guiding the tool 

#

-  for cutting long grass slowly swing the tool from right to 

left and vice versa

-  for cutting shorter grass tilt the tool as illustrated

-  for trimming edges turn the cutting head 180° as 

illustrated

-  hold tool irmly with both hands, so you will have full 

control of the tool at all times

-  maintain a stable working position

-  always hold the tool well away from your body

•  Line feeding 

$

-  tap button F lightly on the ground (preferably on a solid 

surface) while the motor is running

-  two cutting lines will be released and cut of to the 

correct length by line cutting blade G

!  ensure that the red cover D 

2

 is removed from 

the line cutting blade before using the tool

!  take care against injury from line cutting blade G

-  after line feeding always return the tool to its normal 

operating position before switching on

-  feed the lines regularly to maintain full cutting circle

-  when the motor runs without load and no grass is cut, 

the cutting lines are worn or broken; rewind the spool 

or replace the spool system

•  Rewinding spool 

%

In case the cutting lines fail to protrude from spool cap H

!  switch off the tool and disconnect the plug

-  remove spool system from tool and take out spool from 

spool cap H

-  tightly rewind both cutting lines evenly in layers in 

arrow direction

-  insert both lines into spool slots X and ensure that they 

are securely in place (leave suicient length of line)

-  thread both lines through spool holes Y before placing 

the rewound spool into spool cap H

!  ensure that the spool is located securely in place, 

then release both lines from slots X by pulling 

them firmly

-  mount spool system onto tool (

turn spool clockwise 

until it clicks into place

) 

^

•  Replacing spool system 

^

!  switch off the tool and disconnect the plug

-  simply remove/mount old/new spool system as 

illustrated

-  only use SKIL spool system 2610Z01354 with this tool 

(

damage due to using other spool systems will be 

excluded from the warranty

)

-  after replacing the spool system test-run the tool for at 

least one minute without load to ensure that the tool is 

operating properly

!  be sure tool is switched off when plugging in

mAINTENANCE / SERVICE

•  This tool is not intended for professional use

•  Always disconnect plug from power source before 

cleaning and/or maintenance

•  Always keep tool and cord clean (especially the 

ventilation slots)

-  clean the tool with a damp cloth (do not use cleaning 

agents or solvents)

-  clean line cutting blade G 

2

 and cutting guard A 

2

after each use