Makita LXT DUR189Z - Инструкция по эксплуатации - Страница 9

9 ENGLISH

14. 

Keep fingers away from switch trigger when 

not operating the tool and when moving from 

one operating position to another.

Intended use of the tool

1. 

Use right tool. The cordless grass trimmer is 

only intended for cutting grass, light weeds. It 

should not be used for any other purpose such 

as hedge cutting as this may cause injury.

Personal protective equipment

► 

Fig.1

► 

Fig.2

1. 

Dress Properly. The clothing worn should be 

functional and appropriate, i.e. it should be 

tight-fitting but not cause hindrance. Do not 

wear either jewelry or clothing which could 

become entangled with high grass. Wear pro-

tective hair covering to contain long hair.

2. 

When using the tool, always wear sturdy shoes 

with a non-slip sole. This protects against 

injuries and ensures a good footing.

3. 

Always wear protective goggles to protect 

your eyes from injury when using power tools.

The goggles must comply with ANSI Z87.1 in 

the USA, EN 166 in Europe, or AS/NZS 1336 

in Australia/New Zealand. In Australia/New 

Zealand, it is legally required to wear a face 

shield to protect your face, too.

It is an employer's responsibility to enforce 

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

Electrical and battery safety

1. 

Avoid dangerous environment. Don't use the 

tool in damp or wet locations or expose it to 

rain. Water entering the tool will increase the 

risk of electric shock.

2. 

Recharge only with the charger specified by 

the manufacturer. A charger that is suitable for 

one type of battery pack may create a risk of 

fire when used with another battery pack.

3. 

Use power tools only with specifically desig

-

nated battery packs. Use of any other battery 

packs may create a risk of injury and fire.

4. 

When battery pack is not in use, keep it away 

from other metal objects, like paper clips, 

coins, keys, nails, screws or other small metal 

objects, that can make a connection from one 

terminal to another. Shorting the battery termi-

nals together may cause burns or a fire.

5. 

Under abusive conditions, liquid may be 

ejected from the battery; avoid contact. If con

-

tact accidentally occurs, flush with water. If 

liquid contacts eyes, seek medical help. Liquid 

ejected from the battery may cause irritation or 

burns.

6. 

Do not dispose of the battery(ies) in a fire. The 

cell may explode. Check with local codes for 

possible special disposal instructions.

7. 

Do not open or mutilate the battery(ies). 

Released electrolyte is corrosive and may 

cause damage to the eyes or skin. It may be 

toxic if swallowed.

8. 

Do not charge battery in rain, or in wet 

locations.

Starting up the tool

► 

Fig.3

1. 

Make sure that there are no children or other 

people within a working range of 15 meters 

(50 ft), also pay attention to any animals in the 

working vicinity. Otherwise stop using the tool.

2. 

Before use always check that the tool is safe 

for operation. Check the security of the cutting 

tool and the guard and the switch trigger/lever 

for easy and proper action. Check for clean 

and dry handles and test the on/off function of 

the switch.

3. 

Check damaged parts before further use of 

the tool. A guard or other part that is damaged 

should be carefully checked to determine 

that it will operate properly and perform its 

intended function. Check for alignment of 

moving parts, binding of moving parts, break-

age of parts, mounting, and any other condi-

tion that may affect its operation. A guard or 

other part that is damaged should be properly 

repaired or replaced by our authorized ser-

vice center unless indicated elsewhere in this 

manual.

4. 

Switch on the motor only when hands and feet 

are away from the cutting tool.

5. 

Before starting make sure that the cutting 

tool has no contact with hard objects such as 

branches, stones etc. as the cutting tool will 

revolve when starting.

6. 

Make sure there are no electrical cables, water 

pipes, gas pipes etc. that could cause a hazard 

if damaged by use of the tool.

Method of operation

1. 

Never operate the machine with damaged 

guards or without the guards in place.

2. 

Only use the tool in good light and visibility. 

During the winter season beware of slippery 

or wet areas, ice and snow (risk of slipping). 

Always ensure a safe footing.

3. 

Take care against injury to feet and hands from 

the cutting tool.

4. 

Keep hands and feet away from the cutting 

means at all times and especially when switch-

ing on the motor.

5. 

Never cut above waist height.

6. 

Never stand on a ladder and run the tool.

7. 

Never work on unstable surfaces.