Триммеры Einhell PXC GE-CT 36/30 Li E-solo 3411300 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
GB
- 28 -
7.3 Replacing the cutting line
Danger! Remove the battery packs!
1. Fig. 18 Press the line spool housing together
at the points marked M and remove the spool
cover.
2. Remove the empty line spool and the pressi-
on spring.
3. Remove any remaining cutting line if there is
any.
4. Fig. 20 Insert the new cutting line through the
line mount inside the spool.
5. Wind the line with tension in a counter-clock-
wise direction.
6. Fig. 21 Hook the line, approx. 15 cm before
the end of the line, into one of the line holders
on the edge of the spool.
7. Fig. 19 Thread the end of the line on the new
line spool through the eyelet (P) in the spool
cover. Place the pression spring (N) in the line
spool.
8. Pull the line sharply to release it from the line
holder.
9. Press the spool cover back into the line spool
housing.
When you start the equipment again the line will
be cut to the perfect length automatically.
Caution! Bits of the nylon line could cause injury
when
fl
ung out.
7.4 Sharpening the guard hood blade
The guard hood blade (Fig. 2/Item 14) can be-
come blunt over time. When you notice this, undo
the screw holding the guard hood blade on the
guard hood. Clamp the blade in a vise. Sharpen
the blade with a
fl
at
fi
le and make sure that the
angle of the cutting edge is not altered in the pro-
cess. File in one direction only.
7.5 Replacing the cutting line cover (Fig. 22)
If you need to replace the line safety guard (13),
remove any screws if there are any, press the lugs
(R) in and pull o
ff
the line safety guard. Press the
lugs (R) on the new line safety guard (13) into the
location holes provided.
7.6 Maintenance
There are no other parts inside the equipment
which require maintenance.
7.7 Ordering spare parts
Please provide the following information on all
orders for spare parts:
•
Model/type of the equipment
•
Article number of the equipment
•
ID number of the equipment
•
Spare part number of the required spare part
For our latest prices and information please go to
www.isc-gmbh.info
Spare line spool Art. No.: 34.050.96
8. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Defective components must be dispo-
sed of as special waste. Ask your dealer or your
local council.
9. Storage
Store the equipment and accessories in a dark
and dry place at above freezing temperature. The
ideal storage temperature is between 5 and 30 °C.
Store the electric tool in its original packaging.
The equipment has an integrated wall holder (Fig.
23/Item L) to enable it to be hung on the wall.
10. Transport
•
Always carry the tool with one hand on the
handle and the other on the additional handle.
Do not carry the tool by the motor housing.
•
Secure the tool against slipping if transporting
it by car.
•
If possible, use the original packaging for
transportation.
11. Faults
The equipment does not work:
Check that the battery is charged and whether
the charging unit is working. If the equipment will
not work in spite of the voltage supply being OK,
please send it to the customer service address
below.
Anl_GE_CT_36_30_Li_E_SPK9.indb 28
Anl_GE_CT_36_30_Li_E_SPK9.indb 28
03.11.2017 11:25:48
03.11.2017 11:25:48
