Einhell PXC GE-CT 36/30 Li E-solo 3411300 - Инструкция по эксплуатации - Страница 27

GB

- 27 -

Please note: Even if it is used carefully, cutting 

around foundations, stone or concrete walls, etc. 

will result in the line su

ff

 ering above normal wear.

Trimming/mowing

Swing the trimmer from side to side in a scything 

motion. Always keep the line spool parallel to the 

ground. Check the site and decide what cutting 

height you require. Guide and hold the line spool 

at the required height to ensure that you cut even-

ly.

Low trimming

Hold the trimmer right in front of you at a slight 

angle so that the underside of the line spool is 

above the ground and the line strikes the correct 

target. Always cut away from yourself. Never draw 

the trimmer towards yourself.

Cutting along fences/foundations

Edge guide recommended!

When cutting approach wire mesh fences, lath 

fences, natural stone walls and foundations slowly 

so that you can cut close to them without striking 

the obstacle with the line. If, for example, the line 

strikes stones, stone walls or foundations, it will 

wear or fray. If the line strikes wire fencing it will 

break.

Trimming around trees

Edge guide recommended!

When trimming around tree trunks, approach 

slowly so that the line does not strike the bark. 

Walk around the tree, cutting from left to right. Ap-

proach grass or weeds with the tip of the line and 

tilt the line spool forwards slightly. Warning: Take 

extreme care during mowing work. When doing 

such work keep a distance of 30 meters between 

yourself and other people or animals.

Mowing

For mowing you want to cut all the vegetation 

down to the ground. To do this, set the line spool 

at an angle of 30° to the right. Place the handle in 

the required position. Remember the increased 

risk of injury to the user, watchers and animals 

and the danger of damaging other items due to 

objects (for example stones) being thrown out 

(Fig. 17).

Warning: Do not remove any objects from foot-

paths, etc. using the equipment. 

The equipment is a powerful tool and can throw 

small stones and other objects a distance of 15 

meters or more, causing injuries and damage to 

cars, houses and windows.

Sawing

The equipment is not suitable for sawing.

7.  Cleaning, maintenance and 

ordering of spare parts

Danger! 

Before putting away or cleaning the grass trimmer, 

switch o

ff

  and remove the battery pack.

7.1 Cleaning

• 

Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it down with compressed air at 

low pressure. 

• 

We recommend that you clean the equipment 

immediately after you use it.

• 

Clean the equipment regularly with a damp 

cloth and some soft soap. Do not use cleaning 

agents or solvents; these may be aggressive 

to the plastic parts in the equipment. Ensure 

that no water can get into the interior of the 

equipment. The ingress of water into an elec-

tric tool increases the risk of an electric shock.

• 

Use a brush to remove deposits from the sa-

fety guard.

7.2 Replacing the line spool

Danger! Remove the battery packs!

1.  Fig. 18 Press the line spool housing together 

at the points marked M and remove the spool 

cover.

2.  Remove the empty line spool and the pressi-

on spring.

3.  Fig. 19 Thread the end of the line on the new 

line spool through the eyelet (P) in the spool 

cover and allow approx. 13 cm of line to pro-

ject. Place the pression spring (N) in the line 

spool. 

4.  Press the spool cover back into the line spool 

housing.

Anl_GE_CT_36_30_Li_E_SPK9.indb   27

Anl_GE_CT_36_30_Li_E_SPK9.indb   27

03.11.2017   11:25:48

03.11.2017   11:25:48