Makita HG6031VK - Инструкция по эксплуатации - Страница 6

6 English

Q

Make sure that the tool is switched off and the nozzle has cooled down.

Q

Falling down nozzle may ignite objects on the floor. Nozzles must be mounted firmly and 

secure on the unit.

Q

Touching a hot nozzle can lead to serious burn.Before attaching or replacing a nozzle, 

allow the unit to cool down completely or use a suitable tool.

Q

A hot nozzle can set a surface on fire. Place down hot nozzles only on fire-proof surfaces.

Q

An incorrect or defective nozzle can lead to heat accumulation and damage the unit. Use 

only original nozzles according to the table that are suitable for your unit.

INSTRUCTIONS FOR USE

Q

Always observe the safety instructions and appli-

cable regulations.

Q

Use only one hand to hold the tool, do not 

place your other hand over the air vents prior to 

operation:

Q

Mount the correct accessory for the application.

Q

Set the desired air temperature. 

Switching on and off 

Q

To switch the tool on, set the on/off switch to 

position 1/2/3. Some smoke may be emitted after 

switching on, this does not indicate a problem.

Q

To switch the tool off, adjust the lowest tem

-

perature to cool off, then set the on/off switch to 

position 0. Let the tool cool down before moving 

or storing it.

Temperature setting

Q

Turn ON/OFF switch to 1/2/3, depending on tem-

perature you need. 

Detachable front cover

Q

The front cover can be removed when working at 

a narrow area.

Be careful of the hot nozzle. 

Removing the front cover increases the 

risk of burn with the bare hot nozzle.

Stripping paint 

Q

Mount an appropriate accessory.

Q

Set a high air temperature.

Q

Switch the tool on.

Q

Direct the hot air onto the paint to be removed.

Q

When the paint softens, scrape the paint away 

using a hand scraper.

Do not strip metal window frames, as 

the heat may be conducted onto the 

glass and crack it. When stripping 

other window frames, use the glass 

protection nozzle.
Do not keep the tool directed at one 

spot too long to prevent igniting the 

surface.
Avoid collecting paint on the scraper 

accessory, as it may ignite. If neces-

sary, carefully remove paint debris 

from the scraper accessory using a 

knife.

Stationary use

This tool can also be used in stationary mode.

Q

Place the tool onto a stable workbench.

Q

Secure the cable to prevent pulling the tool off the 

workbench.

Q

Carefully switch the tool on.

Make sure that the nozzle always 

points away from you and any 

bystanders.

Make sure not to drop anything into 

the nozzle.

Cooling down

The nozzle and accessory become very hot during use. 

Let them cool down before attempting to move or store 

the tool.

Q

To reduce the cooling time, switch the tool on at 

the lowest air temperature setting and let it run for 

a few minutes.

Q

Switch the tool off and let it cool down for at least 

30 minutes. Always place it vertical and standing.

MAINTENANCE AND CLEANING

Attention! Before performing any 

work on the equipment, pull the 

power plug.

Maintenance 

Q

Your Power Tool has been designed to operate 

over a long period of time with a minimum of 

maintenance. Continuous satisfactory opera-

tion depends upon proper tool care and regular 

cleaning.

Lubrication 

Q

Your power tool requires no additional lubrication.

Cleaning 

Q

Keep the ventilation slots clear and regularly clean 

the housing with a soft cloth.

Cleaning  

Q

Keep the ventilation slots of the machine clean to 

prevent overheating of the motor.

Q

Regularly clean the machine housing with a soft 

cloth, preferably after each use.

Q

Keep the ventilation slots free from dust and dirt.

Q

If the dirt does not come off use a soft cloth moist-

ened with soapy water.