Makita HG6031VK - Инструкция по эксплуатации - Страница 4

4 English

Q

Dress properly. Do not wear loose clothing or 

jewellery. Keep your hair, clothing and gloves 

away from moving parts.

 Loose clothes, jewel

-

lery or long hair can be caught in moving parts.

Q

 If devices are provided for the connection of 

dust extraction and collection facilities, ensure 

these are connected and properly used. 

Use of 

these devices can reduce dust related hazards.

Power tool use and care

Q

Do not force the power tool. Use the correct 

power tool for your application.

 The correct 

power tool will do the job better and safer at the 

rate of which it was designed.

Q

Do not use the power tool if the switch does 

not turn it on and off.

 Any power tool that cannot 

be controlled with the switch is dangerous and 

must be repaired.

Q

Disconnect the plug from the power source 

before making any adjustments, changing 

accessories, or storing power tools.

 Such pre-

ventive safety measures reduce the risk of starting 

the power tool accidentally.

Q

Store idle power tool out of the reach of chil-

dren and do not allow persons unfamiliar with 

the power tool of these instructions to operate 

the power tool.

 Power tools are dangerous in the 

hands of untrained users.

Q

Maintain power tools. Check for misalignment 

or sticking of moving parts, breakage of parts 

and other condition that may affect the power 

tool’s operation. 

If damaged, have the power tool 

repaired before use. Many accidents are caused 

by poorly maintained power tools.

Q

Keep cutting tools sharp and clean. 

Properly 

maintained cutting tools with cutting edges are 

less likely to stick and are easier to control. 

Q

Use the power tool, accessories and tool bits 

etc., in accordance with these instructions and 

in the manner intended for the particular type 

of power tool, taking into account the working 

conditions and the work to be performed. 

Use 

of the power tool for operations different from 

intended could lead to a hazardous situation.

Service

Q

Have your power tool serviced by qualified 

repair person using only identical replacement 

parts. 

This will ensure that the safety of the power 

tool is maintained.

ADDITIONAL SAFETY 

INSTRUCTIONS FOR HEAT GUN

Q

This appliance is not intended for use by per-

sons (including children) with reduced phys-

ical,sensory or mental capabilities, or lack of 

experience and knowledge. 

Children should be supervised to ensure that 

they do not play with the appliance.

Q

 A fire may result if the appliance is not used 

with care, therefore

– 

be careful when using the appliance 

in places where there are combustible 

materials;

– 

do not apply to the same place for a long 

time;

– 

do not use in presence of an explosive 

atmosphere;

– 

be aware that heat may be conducted 

to combustible materials that are out of 

sight;

– 

place the appliance on its stand after use 

and allow it to cool down before storage;

– 

do not leave the appliance unattended 

when it is switched on.

Q

 Do not place your hand over the air vents or 

block the vents in any way.

Q

 The nozzle and accessories of this tool 

become extremely hot during use. Let these 

parts cool down before touching.

Q

 Always switch the tool off before putting it 

down.

Q

 Do not leave the tool unattended while it is 

switched on.

Q

 A fire may arise if the appliance is not used 

with care.

Q

 Heat may be conducted to combustible mate-

rials that are out of sight. Do not use in a damp 

atmosphere, where flammable gases may be 

present or near combustible materials.

Q

 Allow the tool to cool fully before storing.

Q

 Ensure adequate ventilation as toxic fumes 

may be produced.

Q

 Do not use as a hairdryer.

Q

 Do not obstruct either the air intake or noz-

zle outlet, as this may cause excessive heat 

build-up resulting in damage to the tool.

Q

 Do not direct the hot air blast at other people.

Q

 Do not touch the metal nozzle as it becomes 

very hot during use and remains hot for up to 

30 minutes after use.

Q

 Do not place the nozzle against anything while 

using or immediately after use.

Q

 Do not poke anything down the nozzle as 

it could give you an electric shock. Do not 

look down the nozzle while the unit is work-

ing because of the high temperature being 

produced.

Q

 Do not allow paint to adhere to the nozzle or 

scraper as it could ignite after some time.

Removing paint

Q

 Do not use this tool to remove paint containing 

lead. The peelings, residue and vapors of paint 

may contain lead, which is poisonous. Any 

pre-1960 building may have been painted in 

the past with paint containing lead and cov-

ered with additional layers of paint. 

Once deposited on surfaces, hand to mouth 

contact can result in the ingestion of lead. 

Exposure even to low levels of lead can cause 

irreversible damage to the brain and nervous 

system. Young and unborn children are partic-

ularly vulnerable.

Q

 When removing paint, ensure that the work 

area is enclosed. Preferably wear a dust mask.

Q

 Do not burn the paint. Use the scraper and 

keep the nozzle at least 25 mm away from the