Einhell GE-LB 36/230 Li E - Инструкция по эксплуатации - Страница 23

GB

- 23 -

• 

 Position the blower tube just above the 

ground and adjust the length of the strap to 

your requirements (see section 6.1).

• 

 Turn on the equipment (see section 6.2).

• 

 Set the desired blowing velocity with the 

speed controller (see section 6.5).

• 

 Channel the air stream forward and walk 

slowly to blow foliage or garden refuse into a 

pile or to clear out hard-to-reach places.

• 

 To increase the blowing velocity for a short 

time, press the “Turbo button” (see section 

6.6).

Danger!

Never gather (blow) hot, combustible or explosive 

materials into piles.

6.3.2 Sucking up foliage

Caution!

• 

 Only use the leaf blower vac in vacuum mode 

if the catch bag is undamaged and properly 

fitted.

• 

 Do not pick up too many leaves in one go as 

this could clog the tube and the shredder.

• 

 To clear any blockages, follow the steps de-

scribed in the section “Clearing blockages”. 

• 

 Do not pick up hard or damp materials.

• 

 Fit the prepared 2-piece suction tube with rol-

lers and carry-handle, harness and catch bag 

(see section 5.3) to the motor housing.

• 

 Check that all the components are correctly 

fastened (see section 5.4).

• 

 Always position the suction tube on the 

ground and adjust the length of the strap to 

your requirements (see section 6.1). The gui-

de rollers (Fig. 1/Item 9) at the bottom end of 

the suction tube will help you to maneuver the 

suction tube on the ground.

• 

 Turn on the equipment (see section 6.2).

• 

 Set the desired suction power with the speed 

controller (see section 6.5).

• 

 To increase the suction power for a short 

time, press the “Turbo button” (see section 

6.6).

6.4  Emptying the catch bag (Fig. 1b)

Empty the catch bag (7) in good time. With a 

nearly full bag, the suction power drops notably. 

Organic waste should be composted.

• 

 Switch off the equipment and remove the bat-

teries.

• 

 Open the zipper on the catch bag (7) and 

shake out the material.

• 

 Close the zip on the catch bag (7) again.

6.5  Speed control (Fig. 10)

The equipment is 

fi

 tted with a variable speed 

trigger. To use it, turn the speed controller (Item 

10) to the desired position. Use the device only 

with the speed which is actually required and 

do not let it run at a speed which is faster than 

necessary.

1 = Minimum speed

MAX = Maximum speed

6.6  Turbo mode (Fig. 11)

If you need higher blowing power or suction pow-

er for a short time, you can press the turbo button 

(Item T). Pressing the turbo button increases the 

speed for a short time and with it the blowing or 

suction power.

Important: Never press the turbo button for 

any longer than necessary, in order to keep 

the noise level down and extend the battery 

operating time.

6.7 Clearing blockages

Danger!

• 

 Switch off the equipment, wait for the moving 

parts to come to a standstill and remove the 

batteries.

• 

 Wear protective gloves

• 

 Use suitable tools (e.g. a wooden stick)

1.  Examine the tube for blockages. Tap the suc-

tion tube carefully or use a wooden stick to 

clear any blockages.

2.  Empty the catch bag and remove it. Remove 

the suction tube.

3.  Examine the openings in the motor housing 

for possible blockages. Remove the blockage 

with a stick if necessary. Make sure that the 

shredder is clear.

7.  Cleaning, maintenance and 

ordering spare parts

Hazard!

Always remove the batteries before starting any 

cleaning work.

7.1 Cleaning

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 We recommend that you clean the device  

Anl_GE_CL_36_230_Li_E_Solo_SPK9.indb   23

Anl_GE_CL_36_230_Li_E_Solo_SPK9.indb   23

31.08.2021   07:35:02

31.08.2021   07:35:02