Indesit W 431 TX - Инструкция по эксплуатации - Страница 25

When the new
washer arrives

Installation and removal

Whether new or just  transported to a new house,
installation is extremely important for the correct
functioning of your washing machine.

The hook to be used in case the drain
hose ends at a height below 60 cm.

If the drains hose empties into a
tub or sink then fit the plastic gui-
de and secure it to the tap.

The guide for draining into tubs
and sinks.

The end of the drain hose must
be positioned so that it cannot
become submerged.
Extensions are unadvisable. In
c a s e   o f   a b s o l u t e   n e e d ,   t h e
extension must have the same
diameter as the original hose and
must not exceed 150 cm. In case
of wall draining pipes, their
efficiency must be checked by
a qualified technician. If the
dwelling is on one of the upper
floors of a building, there may be
drain trap problems causing the
washing machine to load and
unload water continuously.
I n   o r d e r   t o   a v o i d   s u c h   a n
inconvenience, special anti-drain
trap valves are available in
shops.

Electric connection
Before connecting the appliance
to the electric socket, be sure that:
1)  the electric socket is able to

s u s t a i n   t h e   a p p l i a n c e ’s
m a x i m u m   p o w e r   l o a d
indicated on the data plate
and in compliance with the
law;

2)   the supply voltage is included

within the values indicated on
the data plate;

3)   the socket is compatible with

the appliance’s plug. If not, do
not use adapters, but replace
either the socket or the plug;

4)   electric household appliances

must be equipped with an
“earthing” system.

After removing the appliance from
its packaging, check that it is
intact. If in doubt, contact a
qualified technician immediately.
The inside of the machine is
supported, for transportation, by
4 screws on the back panel.

B e f o r e   u s i n g   t h e   w a s h i n g
machine, remove the screws,
remove the spacers together with
the rubber tubes attached to them
(keeping all the parts) and use the
plastic plugs provided to fill in the
holes.
Important: Use the cap (provided)
to close the 3 holes which housed
the stop pin, situated in the right-hand
par t of the lower back of the
washing machine.

Levelling
The washing machine must be
levelled appropriatey in order to
guarantee its correct functioning.
To level the appliance, the front
feet must be adjusted; the angle
o f   i n c l i n a t i o n ,   m e a s u r e d
according to the worktop, must
not exceed 2°. When placed on
carpet, make sure the ventilation
is not reduced.

The front feet are adjustable.

Connection to the water
mains
Water pressure must range within
the values indicated on the data
plate on the rear of your washing
machine. If the water pipes are new
or left unused, then before
connecting the machine run the
water until clear to remove debris.
Connect the inlet hose to a cold
water tap having a ¾ “ BSP thread.
Ensure that the rubber sealing
washers are fitted at each end of
the inlet hose, with the fitter washer
at the tap end.

A

The rubber gasket .

Connect the inlet hose to the
t h r e a d e d   c o n n e c t o r   o n   t h e
machine rear.

Water pipe inlet at the top right.

Connecting the drain hose
There are two hooks (right or left)
on the rear of your washing
machine to which the drain hose
is to be fixed. Insert the other end
in a stand pipe or place it on the
edge of a sink or tub avoiding
excessive kinks and bending. It
should be placed at a height
ranging from 60 to 100 cm. If it is
necessary to fix the end of the
hose at a height below 60 cm from
the ground, it must be fixed in the
appropriate hook placed on the
upper part of the back panel.

Warning!

The company denies all

liability if and when these

norms are not respected.

Plastic bags, expanded

styrofoam, nails and other

packaging parts are not

children’s toys, and are

potentially dangerous.

Retain the transit screws,

spacers and washers.

Should you move house

then these should be

replaced to support the

inside of the machine to

prevent damage when

transporting the machine.

Instructions for installation and use

22