Oursson JM4600/OR - Инструкция по эксплуатации - Страница 9

9

When switching between the «On» and 
«Reverse» positions, be sure to move the 
button to the «Stop» position for 5 seconds to 
stop the auger.

To avoid overheating of the motor, do not use 
this device for more than 10 minutes without 
a pause. The break between cycles should 
be 5 minutes.

Do not place ingredients that are hotter than 
80°C into the feeding bowl. Let them cool 
down.

Do not use a spoon or other foreign objects 
in order to remove the pulp from the pulp 
spout as it may damage the device.

To push the ingredients into the feeding chu-
te, use only the pusher, which is included 
with the device. It is strictly forbidden to push 
ingredients with hands, as this could cause 
injury.

ORDER OF OpERATION, 

Pic.E

1.  Assemble the device, Pic. D. Plug in the device.
2.  Press the power button, Pic. C-2.
3.  Using the pusher, place the prepared ingredients into 

the filling hole, Pic. E. The products should be cut 

into pieces for the JM4600 model. For the JM4700, 
you can use whole or cut ingredients. To place whole 
ingredients, remove the lid from the feeding bowl, Pic. 
B- 11.

Note: 

• 

Follow the cooking guidelines to prepare the ingre-
dients.

•  Do not overfill the feeding bowl.

UTILIZATION, 

Pic. D

Before first use, 

wipe the device with a soft, dry cloth. 

The rest of the parts wash with warm water and deter-
gent. 

Before assembling or disassembling the device 

and / or removing attachments, make sure that the 

device is unplugged. 
Step 1,

 Pic. D-1

Take the filter and place the silicone ring on it, aligning 

the tab on the ring with the slot in the filter. Press lightly 

on the silicone ring. Make sure the silicone ring is firmly 

seated on the filter.

Step 2,

 Pic. C-3

Place the bowl with spouts on the motor unit. For model 
JM4600, align the two marks as shown in the illustration. 
For model JM4700, align the juice and pulp spouts with 
the grooves on the motor block.

Step 3, 

Pic. C-4

Insert the auger/pressure screw into the center of the 
spout bowl by gently pushing and turning until it snaps 
into place.

Step 4,

 Pic. C-5

Insert the filter into the bowl with the spouts, with the 

silicone ring facing down. Note the position of the largest 

ridge on the filter. Make sure the dots on the filter and 

bowl are aligned as shown in the illustration. 

Step 5, 

Pic. C-6

Place the feeding bowl on the bowl with spouts and turn 
it clockwise as shown in the fpicture. Place the lid on the 
feeding bowl (for model JM4700).

Note: Always leave the spout lid open when juicing 
ingredients that produce a lot of foam, Pic. C-1.

The power button is located on the handle of the device.

The key has three positions (Pic. C-2):

ON (



) – turn on; 

0

 – Pause /stop motor;  

REV (



) – Reverse.

Place the pulp container and juice container under 
the respective spouts. After completing the assembly, 
plug in the device.

4.  If a dense mass of ingredients gets stuck in the juicer 

mechanism and impedes the movement of the juice, 
move the button to the “Stop” position until the engine 
comes to a complete stop, then move the button to 
the “Reverse” position. The auger will start to rotate 
in the opposite direction.After a few seconds, again 
move the button to the “Stop” position and after stop-
ping the engine, press “ON”. Repeat this operation if 
necessary. 

5.  At the end of juicing, close the lid at the spout so 

that the remaining juice does not drip onto the table. 

Switch off the device and unplug it.

Note: Freshly squeezed juices are recommended to 
be consumed immediately after preparation, as after 

a while they begin to exfoliate and lose their beneficial 

properties.

pREpARATION REcOMMENDATIONs 

1.  Do not place into the device dried or hard ingredients, 

such as whole grains, fruits with hard seeds, thick-
skinned or ice. This can damage juice maker’s parts.

2.  Beans or grain can be used if they were presoaked 

overnight and boiled. 

3.  Do not press the products without juice content (coco-

nut, sugar cane, whole grains, etc.). 

4.  Do not use ingredients that contain an excessive 

amount of vegetable oil or animal fat. Do not use the 
juice maker for squeezing oil from the ingredients. 
If the plant oil or animal fat falls onto the pressure 
screw, it can reduce performance and damage juice 
maker’s parts.

5.  Do not load pulp into the juice maker. This can lead to 

a shutdown or lock the juice cup’s lid. 

6.  After juicing the ingredients with small seeds, you 

must clean all parts of the device from the seeds. 

7.  The amount of juice depends on the freshness and 

juiciness of the products. The fresher the vegetables 
or fruit, the more juice you can make.