Metabo SE 4000 620045000 - Инструкция по эксплуатации - Страница 11

ENGLISH

en

11

When the depth stop (12) is inserted, the insertion 
depth changes by 0.25 mm per notch. If screw 
insertion has to be deeper: Insert stop sleeve If the 
screw insertion is too deep: Unscrew stop sleeve.
Removal of the depth stop (12) does not alter the 
set screw insertion depth. After refitting, work can 
continue at the same insertion depth.

When screwing in crosshead screws, press 
the machine with the screwdriver bit (13) firmly 

against the screw until the screw is fully inserted; 
otherwise the bit could slip out of the cross recess 
and damage the material.

7.5

Working without depth stop (12)

Adapt the speed of the screwing process by 
carefully pressing in the trigger switch.
When the screwing process is complete, switch off 
the machine by releasing the trigger switch (3).

7.6

LED lamp (depending on the model)

For working in badly lit areas. The LED light (6) 
lights up when the machine is switched on.

Press the machine firmly against the screw until the 
screwing process is complete. 
This is particularly important when inserting dry wall 
screws (with coarse threads) in gypsum 
plasterboards because the large thread pitch of the 
screws means that they are very quickly inserted. 
If the stop sleeve (17) is stiff, it can be removed to 
clean the thread.

.

If the screwdriver bit (13) is fitted very firmly in the bit 
holder (14): remove the screwdriver bit with a pair of 
pliers.

9.1

Only for cordless machines; the 

machine's multifunctional monitoring 

system

If the machine switches off automatically, the 
machine electronics have activated automatic 

protection mode.

In spite of this protective function, overloading 
is still possible with certain applications and 

can result in damage to the machine.

Causes and remedies:

1.

Battery pack almost flat

 (the electronics 

prevent the battery pack from discharging totally 
and avoid irreparable damage).
If one LED is flashing, the battery pack is almost 
flat. (10) If necessary, press the (11) button and 
check the LEDs (10) to see the charge level. If 
the battery pack is almost flat, it must be 
recharged.

2. Long continuous overloading of the machine will 

activate the 

temperature cut-out

.

Leave the machine or battery pack to cool. 

Note: If the battery pack feels very warm, the 
pack will cool more quickly in your "AIR 
COOLED" charger. 
Note: The machine will cool more quickly if you 
operate it at idling speed.

3. If the 

current is too high

 (for example, if the 

machine seizes continuously for long periods), 
the machine switches off.
Switch off the machine at the trigger switch (3). 
Then continue working as normal. Try to prevent 
the machine from seizing.

ENG

Disconnect the mains plug or remove the battery 
pack from the machine before starting any 
maintenance work.
Remove the depth stop (12) regularly and clean it
It is possible that particles deposit inside the power 
tool during operation. This impairs the cooling of the 
power tool.
The power tool should be cleaned regularly, often 
and thoroughly through all front and rear air vents 
using a vacuum cleaner or by blowing in dry air. 
Prior to this operation, separate the power tool from 
the power source and wear protective glasses and 
dust mask.

f

Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements 
and specifications listed in these operating 
instructions. 

A Magazine screw attachment 6.31618
B Screwdriver bits (length: 25 mm)

Recommendation: only use screwdriver bits 
with plug-in ends of this type:

C Battery chargers: ASC Ultra, ASC 15, ASC 30 

and others.

D Battery packs 18 Volt: 5.2 Ah (6.25592); 4.0 Ah 

(6.25591); 2.0 Ah (6.25596)

See www.metabo.com or the catalogue for a 
complete range of accessories.

Repairs to electrical tools must ONLY be carried out 
by qualified electricians! 
Contact your local Metabo representative if you 
have Metabo power tools requiring repairs. See 
www.metabo.com for addresses.
You can download a list of spare parts from 
www.metabo.com.

8. Tips and Tricks

9. Troubleshooting

10. Maintenance

11. Accessories

12. Repairs