Metabo RW 18 LTX 120 601163660 - Инструкция по эксплуатации - Страница 10

ENGLISH

en

10

To switch off release the trigger switch.

Continuous operation:

 With the trigger (3) 

pressed, push in the locking button (4) and release 

the trigger. Press and release the trigger (3) again to 

switch off.

In continuous operation, the machine 

continues running if it is forced out of your 

hands. Therefore, always hold the machine with 

both hands using the handles provided, stand 

securely and concentrate.

7.5 Switching on/off, change speed (for 

cordless machines)

Press locking button (7) and keep pressed, then 

press the trigger (3).
Press the trigger (3) to increase the rotational 

speed.
To switch off release the trigger switch.

Clean the machine regularly.

9.1 Mains powered machines:

-

Overload protection: There is a MAJOR 

reduction in load speed.

 The motor temperature 

is too high! Allow the machine to run at idle speed 

until it has cooled down.

-

Overload protection: There is a SLIGHT 

reduction in load speed.

 The machine is 

overloaded. Reduce the load before continuing to 

work.

-

Restart protection: The machine does not 

start. 

The restart protection is active. If the mains 

plug is inserted with the machine switched on, or if 

the power supply is restored following an 

interruption, the machine does not start up. Switch 

the machine off and on again.

9.2 Cordless machines:

Overload protection: The machine has shut 

down by itself.

 The device is too hot! Allow the 

machine to run at idle speed until it has cooled 

down.

ENG

Only use original Metabo battery packs and Metabo 

accessories.
Battery packs with different capacities. Use battery 

packs only with voltage suitable for your power tool.
Use only accessories which fulfil the requirements 

and specifications listed in these operating 

instructions. 
See www.metabo.com or the catalogue for a 

complete range of accessories.

Repairs to electrical tools must ONLY be carried out 

by qualified electricians! 
Contact your local Metabo representative if you 

have Metabo power tools requiring repairs. See 

www.metabo.com for addresses.
You can download a list of spare parts from 

www.metabo.com.

Observe national regulations on environmentally 

compatible disposal and on the recycling of disused 

machines, packaging and accessories.

Only for EU countries: Never dispose of 

power tools in your household waste! Used 

power tools must be collected separately and 

handed in for environmentally compatible recycling 

in accordance with European Directive 2002/96/EC 

on waste electrical and electronic equipment and its 

implementation in national legal systems.

Special notes regarding cordless machines:

Battery packs may not be disposed of with regular 

waste. Return faulty or used battery packs to your 

Metabo dealer!
Do not allow battery packs to come into contact with 

water!
Before disposal, discharge the battery pack in the 

power tool. Prevent the contacts from short-

circuiting (e. g. by protecting them with adhesive 

tape).

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
P

1

= Rated  input

P

2

= Power output

n

0

= No-load speed

n

1

= On-load speed

G

= Drill spindle thread

D

R

= maximum permitted agitator diameter

D

= Collar diameter

m

= weight with smallest battery pack/weight 

without cord

Measured values determined in conformity with 

EN 60745.

Machine in protection class II

~

 AC Power

 Direct current

The technical specifications quoted are subject to 

tolerances (in compliance with the relevant valid 

standards).

Emission values

These values make it possible to assess the 

emissions from the power tool and to compare 

different power tools. The actual load may be higher 

or lower depending on the operating conditions, the 

condition of the power tool or the accessories. 

Please allow for breaks and periods when the load 

8. Cleaning

9. Troubleshooting

10. Accessories

11. Repairs

12. Environmental Protection

13. Technical Specifications