Metabo PowerMaxx SB 12 601076840 - Инструкция по эксплуатации - Страница 9

ENGLISH

en

9

Original instructions

We hereby declare that these cordless drills/

screwdrivers and impact drills, identified by type 

and serial number *1), meet all relevant 

requirements of directives *2) and standards *3). 

Technical documents for *4) - see page 3.

The drills and impact drills are suitable for drilling in 

metal, wood, plastic and similar materials, and also 

for screw driving and thread tapping.
The impact drills are also suited for drilling in 

masonry, brickwork and stone.
The user bears sole responsibility for any damage 

caused by inappropriate use.
Generally accepted accident prevention 

regulations and the enclosed safety information 

must be observed.

For your own protection and for the 

protection of your power tool, pay 

attention to all parts of the text that are 

marked with this symbol!

WARNING

 – Read the operating 

instructions to reduce the risk of injury.

WARNING – Read all safety warnings, 

instructions, illustrations and 

specifications provided with this power tool.

Failure to follow all instructions listed below may 

result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future 

reference.

Always include these documents when passing on 

your power tool.

Wear ear protectors when impact drilling 

(machines with the designation SB...). 

Exposure 

to noise can cause hearing loss.

Hold the power tool by insulated gripping 

surfaces, when performing an operation where 

the cutting accessory may contact hidden 

wiring.

 Cutting accessory contacting a "live" wire 

may make exposed metal parts of the power tool 

"live" and could give the operator an electric shock.

Safety instructions when using long drill bits:

a) 

Never operate at higher speed than the 

maximum speed rating of the drill bit.

 At higher 

speeds, the bit is likely to bend if allowed to rotate 

freely without contacting the workpiece, resulting in 

personal injury.

b) 

Always start drilling at low speed and with 

the bit tip in contact with the workpiece.

 At 

higher speeds, the bit is likely to bend if allowed to 

rotate freely without contacting the workpiece, 

resulting in personal injury.

c) 

Apply pressure only in direct line with the bit 

and do not apply excessive pressure.

 Bits can 

bend causing breakage and loss of control, 

resulting in personal injury.
Ensure that the spot where you wish to work is free 

of 

power cables, gas lines or water pipes

 (e.g. 

using a metal detector).

A slightly acidic, flammable fluid may leak 

from defective Li-ion battery packs!

If battery fluid leaks out and comes into 

contact with your skin, rinse immediately 

with plenty of water. If battery fluid leaks out 

and comes into contact with your eyes, wash them 

with clean water and seek medical attention 

immediately!

Protect battery packs from water and 

moisture!

Do not use faulty or deformed battery packs!

Do not expose battery packs to fire!

Do not open battery packs!
Do not touch or short circuit battery pack contacts!
If the machine is defective, remove the battery pack 

from the machine.
Remove the battery pack from the machine before 

any adjustment or maintenance is carried out.
Before fitting the battery pack, make sure that the 

machine is switched off.
Keep hands away from the rotating tool!
Remove chips and similar material only when the 

machine is at a standstill.
Secure the workpiece to prevent slipping or rotation 

(e.g. by securing with screw clamps).
LED light (9): do not observe the LED radiation 

directly with optical instruments.

CAUTION Do not stare at operating lamp.

Reducing dust exposure:

WARNING

 - Some dust created by power 

sanding, sawing, grinding, drilling, and other 

construction activities contains chemicals known to 

cause cancer, birth defects or other reproductive 

harm. Some examples of these chemicals are:

- Lead from lead-based paints,

- Crystalline silica from bricks and cement and 

other masonry products, and

- Arsenic and chromium from chemically treated 

lumber.

Your risk from these exposures varies, depending 

on how often you do this type of work. To reduce 

your exposure to these chemicals: work in a well-

ventilated area, and work with approved safety 

1. Declaration of Conformity

2. Specified Conditions of Use

3. General Safety Information

4. Special Safety Instructions