Metabo PowerMaxx SB 12 601076840 - Инструкция по эксплуатации - Страница 10

ENGLISH

en

10

equipment, such as those dust masks that are 

specially designed to filter out microscopic 

particles.
This also applies to dust from other materials such 

as some timber types (like oak or beech dust), 

metals, asbestos. Other known diseases are e.g. 

allergic reactions, respiratory diseases. Do not let 

dust enter the body.
Observe the relevant guidelines and national 

regulations for your material, staff, application and 

place of application (e.g. occupational health and 

safety regulations, disposal).
Collect the particles generated at the source, avoid 

deposits in the surrounding area. 
Use suitable accessories for special work. In this 

way, fewer particles enter the environment in an 

uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:

- do not direct the escaping particles and the 

exhaust air stream towards yourself or nearby 

persons or towards dust deposits,

- use an extraction unit and/or air purifiers,

- ensure good ventilation of the workplace and keep 

it clean using a vacuum cleaner. Sweeping or 

blowing stirs up dust.

- Vacuum or wash protective clothing. Do not blow, 

beat or brush protective gear.

Transport of li-ion battery packs:

The shipping of li-ion battery pack is subject to laws 

related to the carriage of hazardous goods (UN 

3480 and UN 3481). Inform yourself of the currently 

valid specifications when shipping li-ion battery 

packs. If necessary, consult your freight forwarder. 

Certified packaging is available from Metabo. 
Only send the battery pack if the housing is intact 

and no fluid is leaking. Remove the battery pack 

from the machine for sending. Prevent the contacts 

from short-circuiting (e.g. by protecting them with 

adhesive tape).

See page 2.

1 Drill chuck / drill chuck sleeve*

2 Adjusting sleeve (torque control, maximum 

torque) *

3 Adjusting  sleeve 

(screw driving, drilling, impact drilling) *

4 Adjusting  sleeve 

(torque limitation) *

5 Slide-switch (1st/2nd gear)

6 Rotation selector switch (direction of rotation 

setting, transporting safety device)

7 Trigger  switch

8 Handle

9 LED  lights

10 Battery pack release button

11 Battery pack *

12 Capacity and signal indicator *

13 Capacity indicator button *

14 Belt hook *

15 Bit depot *

16 Protective cap *
* equipment-specific

6.1 The machine's multifunctional 

monitoring system

If the machine switches off automatically, the 

machine electronics have activated automatic 

protection mode. A warning signal sounds 

(continuous beeping). The beeping stops after a 

maximum of 30 seconds or when the trigger switch 

(7) is released.

In spite of this protective function, overloading 

is still possible with certain applications and 

can result in damage to the machine.

Causes and remedies:

1.

Battery pack almost flat

 (the electronics 

prevent the battery pack from discharging totally 

and avoid irreparable damage).

If one LED (12) is flashing, the battery pack is 

almost flat. If necessary, press the button (13) 

and check the LED lamps (12) to see the charge 

level. If the battery pack is almost flat, it must be 

recharged.

2. Long continuous overloading of the machine will 

activate the 

temperature cut-out

.

Leave the machine or battery pack to cool. 
Note: The machine will cool more quickly if you 

operate it at idling speed.

3. If the 

current is too high

 (for example, if the 

machine seizes continuously for long periods), 

the machine switches off.
Switch off the machine at the trigger switch (7). 

Then continue working as normal. Try to prevent 

the machine from seizing.

6.2 Battery pack

Charge the battery pack before use.
Recharge the battery pack if performance 

diminishes.
Instructions on charging the battery pack can be 

found in the operating instructions of the Metabo 

charger.
In case of Li-Ion battery packs with capacity and 

signal display (12) (equipment-specific):

- Press the button (13), the LEDs indicate the 

charge level.

- The battery pack is almost flat and must be 

recharged if one LED is flashing.

Removing and inserting the battery pack

Removal: press the battery pack release button (10) 

and pull the battery pack (11) forwards.
Insertion: Slide the battery pack (11) in until it 

engages.

5. Overview

6. Use