Makita TD111DZ - Инструкция по эксплуатации - Страница 4

4 ENGLISH

Important safety instructions for 

battery cartridge

1. 

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery 

charger, (2) battery, and (3) product using battery.

2. 

Do not disassemble battery cartridge.

3. 

If operating time has become excessively 

shorter, stop operating immediately. It may 

result in a risk of overheating, possible burns 

and even an explosion.

4. 

If electrolyte gets into your eyes, rinse them out 

with clear water and seek medical attention right 

away. It may result in loss of your eyesight.

5. 

Do not short the battery cartridge:

(1) 

Do not touch the terminals with any con-

ductive material.

(2) 

Avoid storing battery cartridge in a con-

tainer with other metal objects such as 

nails, coins, etc.

(3) 

Do not expose battery cartridge to water or rain.

A battery short can cause a large current flow, 

overheating, possible burns and even a breakdown.

6. 

Do not store the tool and battery cartridge in 

locations where the temperature may reach or 

exceed 50 °C (122 °F).

7. 

Do not incinerate the battery cartridge even if 

it is severely damaged or is completely worn 

out. The battery cartridge can explode in a fire.

8. 

Be careful not to drop or strike battery.

9. 

Do not use a damaged battery.

10. 

The contained lithium-ion batteries are subject to 

the Dangerous Goods Legislation requirements. 

For commercial transports e.g. by third parties, 

forwarding agents, special requirement on pack

-

aging and labeling must be observed. 

For preparation of the item being shipped, consulting an 

expert for hazardous material is required. Please also 

observe possibly more detailed national regulations. 

Tape or mask off open contacts and pack up the 

battery in such a manner that it cannot move 

around in the packaging.

11. 

Follow your local regulations relating to dis-

posal of battery.

SAVE THESE INSTRUCTIONS.

CAUTION:

Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that 

have been altered, may result in the battery bursting 

causing fires, personal injury and damage. It will also 

void the Makita warranty for the Makita tool and charger.

Tips for maintaining maximum 

battery life

1. 

Charge the battery cartridge before completely dis-

charged. Always stop tool operation and charge the 

battery cartridge when you notice less tool power.

2. 

Never recharge a fully charged battery cartridge. 

Overcharging shortens the battery service life.

3. 

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot 

battery cartridge cool down before charging it.

FUNCTIONAL 

DESCRIPTION

CAUTION:

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before adjusting or checking function on the tool.

Installing or removing battery 

cartridge

CAUTION:

Always switch off the tool before 

installing or removing of the battery cartridge.

CAUTION:

Hold the tool and the battery car-

tridge firmly when installing or removing battery 

cartridge.

 Failure to hold the tool and the battery 

cartridge firmly may cause them to slip off your hands 

and result in damage to the tool and battery cartridge 

and a personal injury.

1

2

3

►    

1.

 Red indicator 

2.

 Button 

3.

 Battery cartridge

To remove the battery cartridge, slide it from the tool 

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the 

battery cartridge with the groove in the housing and slip 

it into place. Insert it all the way until it locks in place 

with a little click. If you can see the red indicator on the 

upper side of the button, it is not locked completely.

CAUTION:

Always install the battery cartridge 

fully until the red indicator cannot be seen.

 If not, 

it may accidentally fall out of the tool, causing injury to 

you or someone around you.

CAUTION:

Do not install the battery cartridge 

forcibly.

 If the cartridge does not slide in easily, it is 

not being inserted correctly.

Battery protection system

The tool is equipped with a battery protection system. 

This system automatically cuts off power to the motor to 

extend battery life.

The tool will automatically stop during operation if the 

tool and/or battery are placed under one of the following 

conditions: