Makita DHP486RTJ - Инструкция по эксплуатации - Страница 5

5 ENGLISH

NOTE:

 The declared vibration total value(s) has been 

measured in accordance with a standard test method 

and may be used for comparing one tool with another.

NOTE:

 The declared vibration total value(s) may also 

be used in a preliminary assessment of exposure.

WARNING:

The vibration emission during actual 

use of the power tool can differ from the declared val

-

ue(s) depending on the ways in which the tool is used 

especially what kind of workpiece is processed.

WARNING:

Be sure to identify safety measures 

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (tak-

ing account of all parts of the operating cycle such 

as the times when the tool is switched off and when 

it is running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A 

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING:

Read all safety warnings, instruc-

tions, illustrations and specifications provided 

with this power tool.

 Failure to follow all instructions 

listed below may result in electric shock, fire and/or 

serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your 

mains-operated (corded) power tool or battery-operated 

(cordless) power tool.

Cordless hammer driver drill safety 

warnings

Safety instructions for all operations

1. 

Wear ear protectors when impact drilling.

Exposure to noise can cause hearing loss.

2. 

Use the auxiliary handle(s).

 Loss of control can 

cause personal injury.

3. 

Hold the power tool by insulated gripping 

surfaces, when performing an operation where 

the cutting accessory or fasteners may contact 

hidden wiring. 

Cutting accessory or fasteners 

contacting a "live" wire may make exposed metal 

parts of the power tool "live" and could give the 

operator an electric shock.

4. 

Always be sure you have a firm footing. Be 

sure no one is below when using the tool in 

high locations.

5. 

Hold the tool firmly.

6. 

Keep hands away from rotating parts.

7. 

Do not leave the tool running. Operate the tool 

only when hand-held.

8. 

Do not touch the drill bit or the workpiece 

immediately after operation; they may be 

extremely hot and could burn your skin.

9. 

Some material contains chemicals which may 

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier 

safety data.

10. 

If the drill bit cannot be loosened even you 

open the jaws, use pliers to pull it out.

 In such a 

case, pulling out the drill bit by hand may result in 

injury by its sharp edge.

11. 

Make sure there are no electrical cables, water 

pipes, gas pipes etc. that could cause a hazard 

if damaged by use of the tool.

Safety instructions when using long drill bits

1. 

Never operate at higher speed than the maximum 

speed rating of the drill bit.

 At higher speeds, the 

bit is likely to bend if allowed to rotate freely without 

contacting the workpiece, resulting in personal injury.

2. 

Always start drilling at low speed and with the 

bit tip in contact with the workpiece.

 At higher 

speeds, the bit is likely to bend if allowed to rotate 

freely without contacting the workpiece, resulting 

in personal injury.

3. 

Apply pressure only in direct line with the bit 

and do not apply excessive pressure.

 Bits can 

bend causing breakage or loss of control, resulting 

in personal injury.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity 

with product (gained from repeated use) replace 

strict adherence to safety rules for the subject 

product. MISUSE or failure to follow the safety 

rules stated in this instruction manual may cause 

serious personal injury.

Important safety instructions for 

battery cartridge

1. 

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery 

charger, (2) battery, and (3) product using battery.

2. 

Do not disassemble or tamper the battery 

cartridge.

 It may result in a fire, excessive heat, 

or explosion.

3. 

If operating time has become excessively 

shorter, stop operating immediately. It may 

result in a risk of overheating, possible burns 

and even an explosion.

4. 

If electrolyte gets into your eyes, rinse them out 

with clear water and seek medical attention right 

away. It may result in loss of your eyesight.

5. 

Do not short the battery cartridge:

(1) 

Do not touch the terminals with any con-

ductive material.

(2) 

Avoid storing battery cartridge in a con-

tainer with other metal objects such as 

nails, coins, etc.

(3) 

Do not expose battery cartridge to water 

or rain.