Felisatti ДА-10/14.4Л2 4250.5.1.00 - Инструкция по эксплуатации - Страница 29

Шуруповерты Felisatti ДА-10/14.4Л2 4250.5.1.00 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.

Если остались вопросы, задайте их в комментариях после инструкции.

"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
Страница:
/ 31
Загружаем инструкцию
background image

29

OPERATION 

Screwdriving operation 

Place the point of the driver bit in the screw head and apply pressure to the 

tool. Start the tool slowly andthen increasethe speed gradually. Release the 

switch trigger as soon asthe clutch cuts in. 

 

NOTE: 

 Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit 

may be damaged. 

  When  driving  wood  screws,  predrill  pilot  holes  to  make  driving  easier  and  to  prevent 

splitting of the workpiece.   

 If the tool is operated continuously until the battery cartridge has discharged, allow the tool 

to rest for 15 minutes before proceeding with a fresh battery. 

Drilling in wood 

When  drilling  in  wood,  the  best  results  are  obtained  withwood  drills 

equipped  with  a  guide  screw.  The  guide  screwmakes  drilling  easier  by 

pulling the bit into the workpiece. 

Drilling in metal 

To prevent the bit from slipping when starting a hole, makean indentation 

with a center-punch and hammer at the pointto be drilled. Place the point 

of the bit in the indentation andstart drilling. 

Use  a  cutting  lubricant  when  drilling  metals.  The  exceptionsare  iron  and  brass 

which should be drilled dry. 

 

CAUTION: 

 Pressing excessively on the tool will not speed up thedrilling. In fact, this excessive 

pressure will only serve todamage the tip of your bit, decrease the toolperformance 
and shorten the service life of the tool. 

 There is a tremendous force exerted on the tool/bit at thetime of hole break through. Hold 

the tool firmly and exertcare when the bit begins to break through the workpiece. 

  A  stuck  bit  can  be  removed  simply  by  setting  thereversing  switch  to  reverse  rotation  in 

order to back out.However, the tool may back out abruptly if you do nothold it firmly. 

 Always secure small workpieces in a vise or similar hold-downdevice. 

 If the tool is operated continuously until the batterycartridge has discharged, allow the tool 

to rest for 15minutes before proceeding with a fresh battery. 
 
 
 
 

Содержание

Полезные видео

Характеристики

Оцените статью
tehnopanorama.ru
Остались вопросы?

Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)

Задать вопрос

Часто задаваемые вопросы
Как посмотреть инструкцию к Felisatti ДА-10/14.4Л2 4250.5.1.00?
Необходимо подождать полной загрузки инструкции в сером окне на данной странице
Руководство на русском языке?
Все наши руководства представлены на русском языке или схематично, поэтому вы без труда сможете разобраться с вашей моделью
Как скопировать текст из PDF?
Чтобы скопировать текст со страницы инструкции воспользуйтесь вкладкой "HTML"