Fein ASCM 12 Q Select 71161064000 - Инструкция по эксплуатации - Страница 21

21

en

Safety warnings for drills.
Safety instructions for all operations.

Hold the power tool by insulated gripping surfaces, 
when performing an operation where the cutting acces-
sory or fasteners may contact hidden wiring or its own 
cord. 

Cutting accessory contacting a “live” wire may 

make exposed metal parts of the power tool “live” and 
could give the operator an electric shock.

Safety instructions when using long drill bits.

Never operate at higher speed than the maximum speed 
rating of the drill bit. 

At higher speeds, the bit is likely 

to bend if allowed to rotate freely without contacting 
the workpiece, resulting in personal injury.

Always start drilling at low speed and with the bit tip in 
contact with the workpiece. 

At higher speeds, the bit is 

likely to bend if allowed to rotate freely without con-
tacting the workpiece, resulting in personal injury.

Apply pressure only in direct line with the bit and do not 
apply excessive pressure. 

Bits can bend causing break-

age or loss of control, resulting in personal injury.

Special safety instructions.

Beware of any concealed electric cables, gas or water 
conduits. 

Check the working area before commencing 

work, e. g. with a metal detector.

Wear personal protective equipment. Depending on 
application, use face shield, safety goggles or safety 
glasses. Where appropriate, wear dust mask, hearing 
protectors, gloves and workshop apron capable of stop-
ping small abrasive or workpiece fragments. 

The eye 

protection must be capable of stopping flying debris 
generated by various operations. The dust mask or res-
pirator must be capable of filtrating particles generated 
by your operation. Prolonged exposure to high inten-
sity noise may cause hearing loss.

Secure the work piece firmly. 

A work piece that is 

gripped tightly in a clamping device or vice, is more 
secure than if held by hand.

Hold the power tool firmly. 

High reaction torque can 

briefly occur.

Do not work materials containing magnesium. 

Danger 

of fire.

Do not work CFP (carbon-fiber-reinforced polymer) and 
materials containing asbestos. 

These materials are con-

sidered carcinogenic.

Do not rivet or screw any name-plates or signs onto the 
power tool. 

If the insulation is damaged, protection 

against an electric shock will be ineffective. Adhesive 
labels are recommended.

Do not use accessories which are not specifically 
designed and recommended by the power tool manu-
facturer. 

Safe operation is not ensured merely because 

an accessory fits your power tool.

Clean the ventilation openings on the power tool at reg-
ular intervals using non-metal tools. 

The blower of the 

motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.

Never look or stare into the light of the power tool’s 
lamp from a short distance. Never point the light of the 
lamp into the eyes of other persons in close vicinity. 

The radiation produced by the lamp can be harmful for 
the eye.

Do not direct the power tool against yourself, other per-
sons or animals. 

Danger of injury from sharp or hot 

application tools.

Use and handling of the battery (battery pack).

To avoid hazardous situations such as burns, fire, 
explosion, skin injuries, and other injuries when han-
dling the battery, observe the following instructions:

Batteries must not be disassembled, opened or reduced 
in size. Do not subject batteries to mechanical impact 
or shock. 

Hazardous vapours and fluid can escape in 

case of damage and improper use of the battery. The 
vapours can irritate the respiratory system. Liquid 
ejected from the battery may cause skin irritations or 
burns.

When battery fluid from a damaged battery has come 
into contact with objects close by, check the respective 
components, clean them or replace them as required.

Keep the battery away from heat and fire. Do not store 
the battery in direct sunlight.

Do not remove the battery from its original packaging 
until it is going to be used.

Before any work on the machine itself, remove the bat-
tery from the power tool. 

If the power tool accidentally 

starts, there is danger of injury.

Remove the battery only when the power tool is 
switched off.

Keep the battery away from children.

Keep the battery clean and protect it against moisture 
and water. 

Clean contaminated battery terminals and 

power tool connections with a dry, clean cloth.

Use only intact original FEIN batteries that are intended 
for your power tool. 

When working with and charging 

incorrect, damaged, repaired or reconditioned batter-
ies, imitations or other brands, there is danger of fire 
and/or explosion.

Follow the safety warnings in the operating instructions 
of the battery charger.

Hand/arm vibrations

The vibration emission level given in this information 
sheet has been measured in accordance with a stand-
ardised test given in EN 62841 and may be used to 
compare one tool with another. It may be used for a 
preliminary assessment of exposure.
The declared vibration emission level represents the 
main applications of the tool. However, if the tool is 
used for different applications, with different accesso-
ries or poorly maintained, the vibration emission may 
differ. This may significantly increase the exposure level 
over the total working period.
An estimation of the level of exposure to vibration 
should also take into account the times when the tool 
is switched off or when it is running but not actually 
doing the job. This may significantly reduce the expo-

OBJ_BUCH-0000000366-001.book  Page 21  Monday, February 18, 2019  3:57 PM