Bosch GSR 18V-60 C - Инструкция по эксплуатации - Страница 18

18

 | English 

1 609 92A 2SJ | (3.8.16)

Bosch Power Tools

Switching On and Off

To 

start

 the machine, press the On/Off switch 

13

 and keep it 

pressed.

The LED 

10

 lights up when the On/Off switch 

13

 is halfway or 

fully pressed, and enables illumination of the screwing loca-
tion in unfavourable light conditions.

To save energy, only switch the power tool on when using it.

Adjusting the Speed

The speed of the switched-on power tool can be variably ad-
justed, depending on how far the On/Off switch 

13

 is 

pressed.

Light pressure on the On/Off switch 

13

 results in a low rota-

tional speed. Further pressure on the switch results in an in-
crease in speed.

Setting the torque

With the torque preselection ring 

3

, the required torque can 

be preselected in 20 steps. The inserted tool is stopped as 
soon as the set torque is reached.

Gear selection, mechanical



The gear selector 5 can be actuated at standstill or 
when the machine is running. However, this should not 
be done while operating at full load or maximum speed.

1st gear:

Low speed range; for working with large drilling diameters.

2nd gear:

High speed range; for drilling with small drilling diameter.

Temperature Dependent Overload Protection

In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or not kept within the 
permitted operating temperature range, the speed is re-
duced. The power tool will not run at full speed again until the 
permitted operating temperature has been reached.

Activation of the temperature-controlled overload protector 
is indicated by the LED 

10

 on the power tool lighting up red. 

To reach the permitted operating temperature range again, 
either switch the gear selector 

5

 to gear 1, run the power tool 

at no load or wait until the LED 

10

 extinguishes. When the LED 

10

 has extinguished, the tool has reached the permitted op-

erating temperature range again.

Protection Against Deep Discharging

The lithium-ion battery is protected against deep discharging 
by the “Electronic Cell Protection (ECP)”. When the battery is 
empty, the machine is switched off by means of a protective 
circuit: The inserted tool no longer rotates.

Rapid Shut-off

The rapid shut-off feature enables better control of the power 
tool. The power tool shuts off in case of sudden and unexpect-
ed rotation of the power tool around the drilling axis.

The rapid shut-off feature is indicated by a flashing LED on the 
power tool.

To 

restart the machine

, release the On/Off switch and then 

actuate again.



Rapid shut-off can trigger only when the power tool is 
running at maximum operating speed and can rotate 
freely around the drill bit axis. 

Choose a suitable work 

position for this. Otherwise, rapid shut-off will not be en-
sured.

Connectivity functions

In conjunction with the 

Bluetooth

®

 Low Energy Module 

GCY 30-4 (accessory), the following connectivity functions 
are available for the power tool:

–

Registration and personalisation

–

Status check, output of warning messages

–

General information and settings

–

Management

Read the corresponding operating instructions for informa-
tion about the 

Bluetooth

®

 Low Energy Module GCY 30-4.

Working Advice



The power tool with inserted 

Bluetooth

®

 Low Energy 

Module GCY 30-4 (accessory) is equipped with a radio 
interface. Local operating restrictions, e. g. in aircraft 
or hospitals, must be observed.



Apply the power tool to the screw only when it is 
switched off. 

Rotating tool inserts can slip off.

An auxiliary tool can be used to remove the screwdriver bit or 
universal bit holder.

Belt Clip

With the belt clip 

6

, the machine can be hung onto a belt. The 

user has both hands free and the machine is always at hand.

Maintenance and Service

Maintenance and Cleaning



Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport 
and storage, remove the battery from the power tool. 

There is danger of injury when unintentionally actuating 
the On/Off switch.



For safe and proper working, always keep the machine 
and ventilation slots clean.

When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare 
parts. Exploded views and information on spare parts can al-
so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions 
concerning our products and their accessories.

In all correspondence and spare parts orders, please always 
include the 10-digit article number given on the nameplate of 
the product.

OBJ_BUCH-2884-001.book  Page 18  Wednesday, August 3, 2016  11:42 AM