Шредеры Fellowes AutoMax 500C fs 46521 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
4
DELAYED START (ON 500C ONLY)
DELAYED START
Close drawer and
press clock icon on
control panel
Press once for
30 minute delay
(one LED will
illuminate)
Press twice for
60 minute delay
(two LEDs will
illuminate)
Press three times for
90 minute delay
(three LEDs will
illuminate)
Press four times to
reset clock
Allows you to delay shredding for 30, 60 or 90 minutes.
If a critical situation occurs while SmartLock™ is engaged and the shredder drawer
needs to be accessed, follow the steps below.
In case of a power outage, SmartLock™ will remain engaged.
Once power is restored, shred cycle will automatically resume.
**To cancel Delayed Start, press and hold Clock icon for 2 seconds
* Shredder will not run if the hatch is not in place. Always replace the
hatch to resume shredding.
Open drawer and
add paper (Note: Pull
firmly to open drawer)
Locate the access
screw on the back of
the machine and turn
counter clockwise with
a 6mm allen wrench.
1
2
TROUBLESHOOTING
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This indicator
will remain illuminated and the shredder will not operate for the duration of the recovery time.
#JO'VMM8IFOJMMVNJOBUFEUIFTISFEEFSXBTUFCJOJTGVMMBOEOFFETUPCFFNQUJFE6TF'FMMPXFTXBTUFCBH
Drawer/Bin Door Open: The shredder will not run if the bin is open. When illuminated, close the bin to resume shredding.
Remove Paper: When illuminated, see Paper Jam section under Advanced Product Features.
1
The service hatch
will begin to rise.
,FFQUVSOJOHVOUJM
the hatch panel
is easily removed
from the top of the
machine.
3
To replace the service
hatch, position hatch
panel back on top of
the machine. Hold
panel in place while
turning the allen
wrench clockwise until
you feel resistance.
2
PRODUCT MAINTENANCE
TO CLEAN THE SENSORS
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors
may become blocked by paper dust causing the motor to run even if there is no paper present.
(Note: two paper detection sensors are located at the bottom of the paper drawer).
"MMDSPTTDVUTISFEEFSTSFRVJSFPJMGPSQFBLQFSGPSNBODF6OEFSPSPWFSPJMJOHB
machine could lead to issues such as diminished sheet capacity, intrusive noise
when shredding and it could ultimately stop running. To avoid these problems, we
recommend you oil your Fellowes
®
AutoMax™ shredder
once per month
.
OILING SHREDDER
FOLLOW OILING PROCEDURE BELOW
Turn off and unplug
shredder
Locate Auto-start
infrared sensor
6TJOHDPUUPOTXBCXJQF
away any contamination
from the paper sensors
Dip cotton swab in
rubbing alcohol
Open paper feed drawer
and place oiled sheets in
drawer
Apply a light coat of
oil between two sheets
of paper
2
1
3
1
2
4
3
Close the paper feed
drawer and press start to
shred the oiled sheets
* Only use a non-aerosol vegetable oil in long
nozzle container such as Fellowes 35250
t 0QFSBUJPONBJOUFOBODFBOETFSWJDFSFRVJSFNFOUTBSFDPWFSFEJO
the instruction manual. Read the entire instruction manual before
operating shredders.
t "WPJEUPVDIJOHFYQPTFEDVUUJOHCMBEFTHFBSTBOEUBDLTVOEFS
shredder head or feed arms.
t 6OQMVHTISFEEFSCFGPSFDMFBOJOHPSTFSWJDJOH
