Skil 1415LC - Инструкция по эксплуатации - Страница 10

10

•  Always disconnect plug from power source before 

making any adjustment or changing any accessory

ACCESSORIES

•  SKIL can assure flawless functioning of the tool only 

when original accessories are used

•  Use only accessories recommended by SKIL

•  For mounting/using non-SKIL accessories observe the 

instructions of the manufacturer concerned

•  Use only accessories with an allowable speed matching 

at least the highest no-load speed of the tool

•  Do not use damaged, deformed or vibrating accessories

•  Handle and store grinding/cutting discs carefully to avoid 

chipping and cracking

•  Protect accessories from impact, shock and grease

•  Never use grinding discs over 32 mm (1 1/4”) Ø

•  Never use drill bits over 3.2 mm (1/8”) Ø

•  Never use a cutting disc for side grinding

•  Never use reducors or adaptors to fit large-hole grinding/ 

cutting discs

BEFORE USE

•  Always check that the supply voltage is the same as the 

voltage indicated on the nameplate of the tool (tools with 

a rating of 230V or 240V can also be connected to a 

220V supply)

• 

Do not work materials containing asbestos

 (asbestos 

is considered carcinogenic)

• 

Secure the workpiece

 (a workpiece clamped with 

clamping devices or in a vice is held more securely than 

by hand)

•  Use completely unrolled and safe extension cords with a 

capacity of 16 Amps (U.K. 13 Amps)

•  Wear protective glasses and hearing protection 

4

, 

protective gloves and sturdy shoes; when necessary, also 

wear an apron

•  Dust from material such as paint containing lead, some 

wood species, minerals and metal may be harmful 

(contact with or inhalation of the dust may cause allergic 

reactions and/or respiratory diseases to the operator or 

bystanders); 

wear a dust mask and work with a dust 

extraction device when connectable

•  Certain kinds of dust are classified as carcinogenic (such 

as oak and beech dust) especially in conjunction with 

additives for wood conditioning; 

wear a dust mask and 

work with a dust extraction device when connectable

•  Follow the dust-related national requirements for the 

materials you want to work with

•  Ensure that the collet size corresponds with the shaft size 

of the accessory

•  Be sure tool is switched off when plugging in

DURING USE

• 

Use auxiliary handle(s), if supplied with the tool

(loss of control can cause personal injury)

• 

Hold power tool by insulated gripping surfaces, 

when performing an operation where the cutting 

accessory may contact hidden wiring or its own 

cord

 (a cutting accessory contacting a “live” wire may 

make exposed metal parts of the power tool “live” and 

could give the operator an electric shock)

•  Always keep the cord away from moving parts of the tool; 

direct the cord to the rear, away from the tool

•  Never use the tool when cord is damaged; have it 

replaced by a qualified person

• 

Never use spindle lock while tool is running

 (damage 

due to improper handling will be excluded from the 

guarantee)

•  Keep hands away from rotating accessories

•  When grinding metal, sparks are generated; keep other 

persons and combustible material from work area

•  Keep the ventilation slots uncovered while working

•  In case of electrical or mechanical malfunction, 

immediately switch off the tool and disconnect the plug

AFTER USE

•  The accessory continues to rotate for a short time after 

the tool has been switched off

•  Before you put down the tool, switch off the motor and 

ensure that all moving parts have come to a complete 

standstill

•  After switching off the tool, never stop the rotation of the 

accessory by a force applied against it

•  Store tool in locations where temperature will not exceed 

50°C

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

•  Do not connect the blue (= neutral) or brown (= live) wire 

in the cord of this tool to the earth terminal of the plug

•  If for any reason the old plug is cut off the cord of this tool, 

it must be disposed of safely and not left unattended

USE

•  Changing accessories 

5

!  switch off the tool and disconnect the plug

!  ensure that collet size corresponds with shaft 

size of accessory

-  push spindle-lock button B and hold it while you turn 

collet nut D by hand until the spindle lock prevents 

further rotation and loosen collet nut D with wrench E

-  insert an accessory in collet C as far as possible to 

minimize run-out and unbalance

-  push spindle-lock button B and hold it while you 

tighten collet nut D with wrench E

!  avoid excessive tightening of collet nut D

!  never tighten collet nut, if there is no accessory 

in collet; collet may be damaged

•  Changing collets 

6

!  switch off the tool and disconnect the plug

-  push spindle-lock button B and hold it while you 

remove collet nut D

-  remove collet C

-  insert new collet

!  never tighten collet nut, if there is no accessory 

in collet; collet may be damaged

•  Before using the tool

-  ensure that accessory is correctly mounted and firmly 

tightened

-  check if accessory runs freely by turning it by hand

-  test-run tool for at least 30 seconds at highest no-load 

speed in a safe position

-  stop immediately in case of considerable vibration or 

other defects and check tool to determine the cause

•  On/off switch 

7

-  switch on/off the tool by pushing knob A in “I”/”O” 

position

!  before the accessory reaches the workpiece, the 

tool should run at full speed