Makita GA5021C - Инструкция по эксплуатации - Страница 6

6 

ENG208-2 

Vibration 

The vibration total value (tri-axial vector sum) 
determined according to EN60745-2-3: 

Work mode : surface grinding 
Vibration emission (a

h,AG

) : 8.5 m/s

2 

Uncertainty (K) : 1.5 m/s

2 

Cutting-off or wire brushing may have different vibration 
emission values. 

ENH101-9 

EC-DECLARATION OF CONFORMITY 

Model; GA5020,GA5020C,GA5021, 
GA5021C,GA6020,GA6020C,GA6021,GA6021C 

We declare under our sole responsibility that this 
product is in compliance with the following standards of 
standardized documents; 
EN60745, EN55014, EN61000 in accordance with 
Council Directives, 2004/108/EC, 98/37/EC. 

CE2008

000230 

Tomoyasu Kato 

Director 

Responsible Manufacturer: 

Makita Corporation

3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN 
Authorized Representative in Europe: 

Makita International Europe Ltd.

Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 
8JD, ENGLAND 

GEB033-2 

SPECIFIC SAFETY RULES 

DO NOT let comfort or familiarity with product 
(gained from repeated use) replace strict adherence 
to grinder safety rules. If you use this tool unsafely 
or incorrectly, you can suffer serious personal 
injury. 
Safety Warnings Common for Grinding, Sanding, 
Wire Brushing, or Abrasive Cutting-Off Operations: 

1. 

This power tool is intended to function as a 
grinder, sander, wire brush or cut-off tool. 
Read all safety warnings, instructions, 
illustrations and specifications provided with 
this power tool.

 Failure to follow all instructions 

listed below may result in electric shock, fire 
and/or serious injury. 

2. 

Operations such as polishing are not 
recommended to be performed with this power 
tool.

 Operations for which the power tool was not 

designed may create a hazard and cause 
personal injury.   

3. 

Do not use accessories which are not 
specifically designed and recommended by 
the tool manufacturer.

 Just because the 

accessory can be attached to your power tool, it 
does not assure safe operation. 

4. 

The rated speed of the accessory must be at 
least equal to the maximum speed marked on 
the power tool.

 Accessories running faster than 

their rated speed can break and fly apart. 

5. 

The outside diameter and the thickness of 
your accessory must be within the capacity 
rating of your power tool.

 Incorrectly sized 

accessories cannot be adequately guarded or 
controlled. 

6. 

The arbour size of wheels, flanges, backing 
pads or any other accessory must properly fit 
the spindle of the power tool.

 Accessories with 

arbour holes that do not match the mounting 
hardware of the power tool will run out of balance, 
vibrate excessively and may cause loss of control. 

7. 

Do not use a damaged accessory. Before each 
use inspect the accessory such as abrasive 
wheels for chips and cracks, backing pad for 
cracks, tear or excess wear, wire brush for 
loose or cracked wires. If power tool or 
accessory is dropped, inspect for damage or 
install an undamaged accessory. After 
inspecting and installing an accessory, 
position yourself and bystanders away from 
the plane of the rotating accessory and run the 
power tool at maximum no-load speed for one 
minute.

 Damaged accessories will normally 

break apart during this test time. 

8. 

Wear personal protective equipment. 
Depending on application, use face shield, 
safety goggles or safety glasses. As 
appropriate, wear dust mask, hearing 
protectors, gloves and workshop apron 
capable of stopping small abrasive or 
workpiece fragments.

 The eye protection must 

be capable of stopping flying debris generated by 
various operations . The dust mask or respirator 
must be capable of filtrating particles generated 
by your operation. Prolonged exposure to high 
intensity noise may cause hearing loss. 

9. 

Keep bystanders a safe distance away from 
work area. Anyone entering the work area 
must wear personal protective equipment.

Fragments of workpiece or of a broken accessory 
may fly away and cause injury beyond immediate 
area of operation. 

10. 

Hold power tool by insulated gripping 
surfaces only, when performing an operation 
where the cutting accessory may contact 
hidden wiring or its own cord.

 Cutting 

accessory contacting a "live" wire may make 
exposed metal parts of the power tool "live" and 
shock the operator. 

11. 

Position the cord clear of the spinning 
accessory.

 If you lose control, the cord may be 

cut or snagged and your hand or arm may be 
pulled into the spinning accessory.