Bosch GEX 18V-125 (0.601.372.201) - Инструкция по эксплуатации - Страница 17

English | 

17

Operation

Starting Operation

Switching On/Off

u

Make sure that you are able to press the On/Off switch
without releasing the handle.

To 

switch on

 the power tool, press the on/off switch 

(1)

.

To 

switch off

 the power tool, press the on/off switch 

(1)

again.

Preselecting the orbital stroke rate

You can even preselect the orbital stroke rate during opera-
tion using the necessary orbital stroke rate preselection
thumbwheel 

(7)

.

1–2

Low orbital stroke rate

3–4

Medium orbital stroke rate

5–6

High orbital stroke rate

The required orbital stroke rate is dependent on the material
and the work conditions and can be determined using prac-
tical tests.
The Constant Electronic keeps the orbital stroke rate at no
load and under load virtually consistent, guaranteeing uni-
form performance.
After working at a low orbital stoke rate for an extended
period, you should operate the power tool at the maximum
orbital stroke rate for approximately three minutes without
load to cool it down.

Application Overview

Application/Material

Abrasive

Speed setting

Removing

– Removing old paint and varnish
– Sanding wood

P60–P100

4–6

– Sanding thermoplastic synthetic materials

P60–P100

1–3

Preparing

– Sanding wood and veneer prior to painting
– Edge chamfering on wooden materials
– Smoothing wooden surfaces before staining

P120–P180

4–6

– Intermediate lacquer sanding and sanding undercoats
– Intermediate lacquer sanding on edges

P220–P280

1–3

Finishing

– Sanding wood
– Sanding solid wood edges and veneer edges

P150–P180

4–6

– Lacquer sanding on stained surfaces and edges

P240–P320

1–3

Working Advice

u

Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.

 There is risk of injury

from unintentionally pressing the on/off switch.

u

Always wait until the power tool has come to a com-
plete stop before placing it down.

u

This power tool is not suitable for bench-mounted use.

It must not be clamped into a vice or fastened to a work-
bench, for example.

For fatigue-free work, you can hold the power tool from
above, from the side or from the front, depending on the ap-
plication (see figure 

G

).

Sanding Surfaces

Switch the power tool on, place the entire sanding surface
against the surface of the workpiece and apply moderate
pressure as you move the sander over the workpiece.
The material removal rate and sanding result are primarily
determined by the choice of sanding sheet, the preselected
orbital stroke rate level and the contact pressure.
Only immaculate sanding sheets achieve good sanding per-
formance and make the power tool last longer.

Be sure to apply consistent contact pressure in order to in-
crease the lifetime of the sanding sheets.
Excessively increasing the contact pressure will not lead to
increased sanding performance, rather it will cause more
severe wear of the power tool and of the sanding sheet.
Use only original 

Bosch

-sanding accessories.

Rough Sanding

Attach a coarse grit sanding sheet.
Apply only light pressure to the power tool so that it runs at a
higher orbital stroke rate and a higher material removal rate
is achieved.

Fine Sanding

Attach a fine grit sanding sheet.
You can reduce the sanding plate orbital stroke rate by
lightly varying the contact pressure or changing the orbital
stroke rate level; the random orbit motion will be retained.
Move the power tool with moderate pressure flat on the
workpiece in a circular motion or alternately along and
across it. Do not tilt the power tool in order to avoid sanding
through the workpiece, e.g. veneers.
Switch the power tool off after completing operation.

Bosch Power Tools

1 609 92A 7N0 | (17.05.2022)