Bosch GEX 18V-125 (0.601.372.201) - Инструкция по эксплуатации - Страница 15

English | 

15

Technical Data

Random orbit sander

GEX 18V-125

Article number

3 601 C72 2..

Rated voltage

V

18

Orbital stroke rate preselec-
tion

●

No-load speed n

0

A)

min

-1

6000–10,000

No-load orbital stroke rate

A)

min

-1

12,000–20,000

Orbit diameter

mm

2.5

Sanding pad diameter

mm

125

Weight according to EPTA-
Procedure 01:2014

A)

kg

1.5–2.5

Recommended ambient tem-
perature during charging

°C

0 to +35

Permitted ambient temperat-
ure during operation

B)

 and

during storage

°C

–15 to +50

Recommended rechargeable
batteries

GBA 18V...

ProCORE18V...

Recommended battery char-
gers

GAL 18...

GAX 18...

GAL 36...

A) Depends on battery in use
B) Limited performance at temperatures <0 °C

Noise/Vibration Information

Noise emission values determined according
to 

EN 62841-2-4

.

Typically, the A-weighted sound pressure level of the power
tool is less than 70 dB(A). The noise level when working can
exceed the volume stated. 

Wear hearing protection!

Vibration total values a

h

 (triax vector sum) and uncertainty K

determined according to 

EN 62841-2-4

:

a

h

 < 

2.0

 m/s

2

, K = 

1.5

 m/s

2

,

The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,
and organising workflows correctly.

Assembly

u

Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage.

 There is risk of injury

from unintentionally pressing the on/off switch.

Battery Charging

u

Use only the chargers listed in the technical data.

 Only

these chargers are matched to the lithium-ion battery of
your power tool.

Note: 

The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.

u

Do not continue to press the On/Off switch after the
power tool has automatically switched off.

 The battery

can be damaged.

Follow the instructions on correct disposal.

Removing the battery

The rechargeable battery 

(4)

 is equipped with two locking

levels to prevent the rechargeable battery from falling out if
the rechargeable battery release button 

(3)

 is pressed unin-

tentionally. The rechargeable battery is held in place by a
spring when fitted in the power tool.
To remove the rechargeable battery 

(4)

, press the release

button 

(3)

 and pull the rechargeable battery to the rear and

out of the power tool. 

Do not use force to do this.

Battery charge indicator

The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator   or 

 to

show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.

Bosch Power Tools

1 609 92A 7N0 | (17.05.2022)