Ryobi R18RS7-0 - Инструкция по эксплуатации - Страница 3

Safety, performance, and dependability have been given 
top priority in the design of your reciprocating saw.

INTENDED USE

The reciprocating saw is intended to be used only by 
adults who have read and understood the instructions and 
warnings in this manual and can be considered responsible 
for their actions.
With appropriate blades 

fi

 tted, the reciprocating saw is 

designed to cut wood, plastics, drywall and metal up 
to the depth described in the speci

fi

 cations table. The 

reciprocating saw is designed for handheld use; it is not to 
be mounted onto a workbench unless speci

fi

 c  instructions 

are given about how to do this by the manufacturer of the 
product.
Do not use the product for any other purpose.

 WARNING

Read all safety warnings, instructions, illustrations 
and specifications provided with this power tool.

Failure to follow all instructions listed below may result in 
electric shock, 

fi

 re and/or serious injury.

Save all warnings and instructions for future reference.

RECIPROCATING SAW SAFETY WARNINGS

■

Hold the power tool by insulated gripping surfaces, 
when performing an operation where the cutting 
accessory may contact hidden wiring.

 Cutting 

accessory contacting a “live” wire may make exposed 
metal parts of the power tool “live” and could give the 
operator an electric shock.

■

Use clamps or another practical way to secure and 
support the workpiece to a stable platform.

 Holding 

the workpiece by hand or against your body leaves it 
unstable and may lead to loss of control.

■

Ambient temperature range for tool during operation is 
between 0°C and 40°C.

■

Ambient temperature range for tool storage is between 
0°C and 40°C.

■

The recommended ambient temperature range for the 
charging system during charging is between 10°C and 
38°C.

 WARNING

Make sure both the blade clamp lever and lock lever are 
fully 

fl

 ipped down before connecting the battery pack or 

turning the product on. Failure to heed this warning could 
result in serious personal injury.

ADDITIONAL BATTERY SAFETY WARNINGS

 WARNING

To reduce the risk of 

fi

 re, personal injury, and product 

damage due to a short circuit, never immerse your 
tool, battery pack or charger in 

fl

 uid or allow a 

fl

 uid  to 

fl

 ow inside them. Corrosive or conductive 

fl

 uids,  such 

as seawater, certain industrial chemicals, and bleach 
or bleach-containing products, etc., can cause a short 
circuit.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national 
provisions and regulations.

Follow all special requirements on packaging and labelling 
when transporting batteries by a third party. Ensure that 
no batteries can come in contact with other batteries 
or conductive materials while in transport by protecting 
exposed connectors with insulating, non-conductive caps 
or tape. Do not transport batteries that are cracked or 
leaking. Check with the forwarding company for further 
advice.

■

Ambient temperature range for battery during use is 
between 0°C and 40°C.

■

Ambient temperature range for battery storage is 
between 0°C and 20°C.

RESIDUAL RISKS

Even when the reciprocating saw is used as prescribed, it is 
still impossible to completely eliminate certain residual risk 
factors. The following hazards may arise and the operator 
should pay special attention to avoid the following:

■

Injury caused by vibration

–

Use the lowest speed setting which achieves the 
task. Limit exposure. See “Risk Reduction”.

■

Injury caused by dust

–

Wear eye protection at all times. Wear appropriate 
dust mask with suitable filters that can protect 
against particles from the material being worked on. 
Do not eat, drink, or smoke in the work area. Ensure 
adequate ventilation.

■

Electric shock

–

The blade may contact hidden wiring causing 
parts of the product to become live. Always hold 
the product by the designated handles and take 
care when blind cutting into walls and floors where 
cables may be hidden.

NOTE: 

When working on walls, ceilings, or floors, take 

care to avoid electric cables and gas or water pipes. 
The product must be operated with both hands.

■

Injury from contact with the cutting blade

–

The blades are very sharp and will become hot 
during use. Wear gloves when changing blades. 
Keep hands away from the cutting area at all times. 
Clamp the workpiece whenever possible.

■

Injury caused by noise

–

Prolonged exposure to noise will increase the risk 
of hearing damage, and the effects are cumulative. 
When using power tools for any extended period of 
time, wear hearing protection.

RISK REDUCTION

It has been reported that vibrations from handheld tools 
may contribute to a condition called Raynaud’s Syndrome 
in certain individuals. Symptoms may include tingling, 
numbness and blanching of the 

fi

 ngers, usually apparent 

upon exposure to cold. Hereditary factors, exposure to 
cold and dampness, diet, smoking, and work practices 
are all thought to contribute to the development of these 
symptoms. There are measures that can be taken by the 
operator to possibly reduce the effects of vibration:

1

 English 

|

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

TR

EL