Metabo PowerMaxx SSE 12 BL - Инструкция по эксплуатации - Страница 11

ENGLISH

en

11

6.3 Removing and inserting the battery pack

To remove the battery pack:

Press the battery pack 

release button (6) and remove the battery  (7) pack.
To fit the battery pack: Slide in the battery pack (7) 

until it engages .

6.4 Fitting and removing the saw blade

Before carrying out any work: Remove the 

battery pack.
Do not touch the saw blade immediately 

following operation of the tool, as it can be 

extremely hot and can lead to skin burns.

Use jigsaw saw blades as a general rule.

1. Turn the clamping sleeve (1) in the direction of 

the arrow and hold it.

2. Insert the saw blade (13) as far as the limit stop 

or remove it.

3. Release the clamping sleeve (1) (the clamping 

sleeve rotates back to its original position).

4. Check that the saw blade is securely seated.

Note

 when using 

jig saw blades:

 Both sabre saw 

and jig saw blades can be used. Use sabre saw 

blades as a general rule. When inserting jig saw 

blades, ensure that the jig saw blade is inserted in a 

vertical position as far as the limit stop. Slowly turn 

the clamping sleeve (1) back to its original position 

and ensure that the jig saw blade is fitting into the 

recess.

Note: 

Should it occur that a saw blade has broken 

off and it cannot be removed by hand from the saw 

blade quick-clamping device, turn the clamping 

sleeve (1) in the direction of the arrow and hold it. 

Engage the tip of a saw blade in the broken section 

and pull it out. A fine-toothed metal saw blade is 

best suited for this task.

6.5 Setting the guide

The cutting depth can be limited by shifting the 

guide (12) (e.g. when sawing in front of a wall). 
Occasionally shift the guide (12) to achieve even 

wear of the saw blade.
1. Press the button (11) and shift the guide (12) to 

the desired position.

2. Release the button (11) and shift the guide until 

it engages.

Check the guide (12) to ensure that it is 

securely fitted.

7.1 Switching on and off, stroke rate, 

switch-on lock

 (4)

:

Trigger (10) locked.
Trigger (10) unlocked.

Switching on, speed:

 Press the trigger (10). The 

stroke rate can be changed by pressing in the 

trigger. 

Switching off:

 Release the trigger (10).

7.2 Working instructions
Sawing:

Use a saw blade geared to the material to be sawn.
Press the machine with the guide (12) against the 

workpiece. Switch on the machine, and only then 

guide the saw blade against the workpiece. 
Do not make contact with any objects or with the 

ground with the moving saw blade (risk of recoil or 

of breaking the saw blade).
Adapt the stroke rate to the material to the sawn.
Avoid excessive pressure on the saw blade 

(particularly in the case of long saw blades).
If the saw blade jams, turn the machine off immedi-

ately. Widen the sawn gap slightly with a suitable 

tool and take out the machine.
After completing the sawing cut, switch off the 

machine and only take it out of the sawn gap to 

place it down once the saw blade has come to a 

standstill (danger of recoil).
Lock the machine with the switch-on lock (4) to 

prevent it from switching on inadvertently.

Plunge cuts:

Plunge cuts may only be made in soft materials 

such as wood or plastic. Only use short saw blades.
Hold the machine with both hands at the intended 

handles, take a secure stance and concentrate on 

the work.
See illustration, page 3: The machine is pressed 

with the edge of the guide (12) against the work-

piece. The saw blade does not make contact with 

the workpiece. Switch on machine. The corner of 

the guide serves as a pivot point around which the 

machine is slowly aligned, whereby the saw blade 

cuts into the workpiece. 

On a regular basis, use compressed air to blow out 

the machine through the motor ventilation slots. 
Clean regularly: Press button (11) and remove 

guide (12). Hold the device downwards in a vertical 

position without the saw blade and, using your 

hand, lightly tap on the machine. The accumulated 

dust falls out. Do not oil or grease.

7. Use

8. Servicing