Bosch 0.601.6A5.002 - Инструкция по эксплуатации - Страница 13

English | 

13

Safety instructions for sabre saws

u

Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting ac-
cessory may contact hidden wiring.

 Cutting accessory

contacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an elec-
tric shock.

u

Use clamps or another practical way to secure and
support the workpiece to a stable platform.

 Holding

the workpiece by hand or against your body leaves it un-
stable and may lead to loss of control.

u

Keep hands away from the sawing area. Do not reach
under the workpiece.

 Contact with the saw blade can

lead to injuries.

u

Hold the power tool firmly with both hands and make
sure you have a stable footing.

 The power tool can be

more securely guided with both hands.

u

Only bring the power tool into contact with the work-
piece when switched on.

 Otherwise there is danger of

kickback if the cutting tool jams in the workpiece.

u

Ensure that the footplate is always resting on the
workpiece while sawing. 

The saw blade can jam and

lead to loss of control over the power tool.

u

When the cut is completed, switch off the power tool
and then pull the saw blade out of the cut only after it
has come to a standstill.

 In this manner you can avoid

kickback and can place down the power tool securely.

u

Always wait until the power tool has come to a com-
plete stop before placing it down.

 The application tool

can jam and cause you to lose control of the power tool.

u

Use only undamaged saw blades that are in perfect
condition.

 Bent or dull saw blades can break, negatively

influence the cut, or lead to kickback.

u

Do not brake the saw blade to a stop by applying side
pressure after switching off.

 The saw blade can be dam-

aged, break or cause kickback.

u

Ensure that the material is securely clamped. Do not
support the workpiece using your hands or feet. Do
not touch any objects or the floor with the saw while it
is running.

 There is a risk of kickback.

u

Use suitable detectors to determine if there are hid-
den supply lines or contact the local utility company
for assistance.

 Contact with electric cables can cause

fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.

u

In case of damage and improper use of the battery, va-
pours may be emitted. The battery can set alight or ex-
plode. 

Ensure the area is well ventilated and seek medical

attention should you experience any adverse effects. The
vapours may irritate the respiratory system.

u

Do not open the battery. 

There is a risk of short-circuit-

ing.

u

The battery can be damaged by pointed objects such
as nails or screwdrivers or by force applied externally.

An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.

u

Only use the battery with products from the manufac-
turer.

 This is the only way in which you can protect the

battery against dangerous overload.

Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture.

 There is a risk of explosion and

short-circuiting.

Product Description and
Specifications

Read all the safety and general instructions.

Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.

Please observe the illustrations at the beginning of this oper-
ating manual.

Intended Use

The power tool is suitable for sawing wood, plastic, metal
and building materials on a firm surface. It is suitable for
straight and curved cuts. When using designated suitable bi-
metal saw blades, flush cutting is also possible. The saw
blade recommendations are to be observed.

Product features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.

(1)

Saw blade

A)

(2)

Base plate

(3)

Locking sleeve for saw blade

(4)

Battery

A)

(5)

Lock-off button for on/off switch

(6)

On/off switch

(7)

Worklight

(8)

Battery release button

A)

(9)

Handle (insulated gripping surface)

(10)

Button for battery charge indicator

A)

(11)

Battery charge indicator

A)

(12)

Saw blade receptacle

A)

Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical data

Reciprocating saw

GSA 18 V-LI C

Article number

3 601 FA5 0..

Rated voltage

V=

18

No-load stroke rate n

0

min

−1

0–3050

Tool holder

SDS

Stroke

mm

21

Bosch Power Tools

1 609 92A 4TC | (02.04.2019)