Metabo MT 18 LTX BL QSL - Инструкция по эксплуатации - Страница 12

ENGLISH

en

12

Note: If the battery pack feels very warm, the 

pack will cool more quickly in an "AIR COOLED" 

charger. 
Note: The machine will cool more quickly if you 

operate it at idling speed.

3.

The machine does not run and the LED light 

(1) flashes. 

The restart protection is active. The 

machine will not start if the battery pack is 

inserted while the machine is on. Switch the 

machine off and on again.

Use only original Metabo or CAS (Cordless Alliance 

System) battery packs and accessories.
Use only accessories that fulfil the requirements 

and specifications listed in these operating instruc-

tions.
Battery packs with different capacities:

Best.-Nr.:  .................. 625596000  2,0 Ah (LiHD)

Best.-Nr.:  .................. 625367000  4,0 Ah (LiHD)

etc.

Chargers: ASC 55, ASC 145, etc.
Best.-Nr.: .................. 627044000  ASC 55

Best.-Nr.: .................. 627378000  ASC 145 

etc.

For a complete range of accessories, see 

www.metabo.com or the main catalogue.

Repairs to electrical tools must ONLY be 

carried out by qualified electricians! 

Contact your local Metabo representative if you 

have Metabo power tools requiring repairs. See 

www.metabo.com for addresses.
You can download a list of spare parts from 

www.metabo.com.

Observe national regulations on environmentally 

compatible disposal and on the recycling of disused 

machines, packaging and accessories.

Only for EU countries: Never dispose of 

power tools in your household waste! Used 

power tools must be collected separately and 

handed in for environmentally compatible recycling 

in accordance with European Directive 2012/19/EU 

on waste electrical and electronic equipment and its 

implementation in national legal systems.
Battery packs may not be disposed of with regular 

waste. Return faulty or used battery packs to your 

Metabo dealer!
Do not allow battery packs to come into contact with 

water!

Before disposal, discharge the battery pack in the 

power tool. Prevent the contacts from short-circu-

iting (e. g. by protecting them with adhesive tape).

Explanatory notes on the specifications on page 3. 

Changes due to technological progress reserved.

U

= Voltage of battery pack

s

0

= Oscillating frequency at idle speed

o

= Oscillation angle left / right

m

= Weight with smallest battery pack

Measured values determined in conformity with EN 

62841.
Permitted ambient temperature during operation: 

-20 °C (-4°F) to 50 °C (120°F) (limited performance 

with temperatures below 0 °C (32°F)). Permitted 

ambient temperature for storage: 0 °C (32°F) to 

30 °C (86°F).

 Direct current

The technical specifications quoted are subject to 

tolerances (in compliance with the relevant valid 

standards).

Emission values

These values make it possible to assess the 

emissions from the power tool and to compare 

different power tools. The actual load may be higher 

or lower depending on the operating conditions, the 

condition of the power tool or the accessories. 

Please allow for breaks and periods when the load 

is lower for assessment purposes. Arrange 

protective measures for the user e.g. organisational 

measures based on the adjusted estimates. 
Vibration total value (vector sum of three directions) 

determined in accordance with EN 62841:

a

h, DS

= Vibration emission value (surface 

grinding)

a

h, S

= Vibration emission value (scraping)

a

h, ST

= Vibration emission value (sawing with 

plunge cutting saw blade)

a

h, SS

= Vibration emission value (sawing with 

segment saw blade)

K

h,...

= Uncertainty (vibration)

Typical A-effective perceived sound levels:

L

pA

= Sound-pressure  level

L

WA

= Acoustic power level

K

pA

, K

WA

= Uncertainty

During operation the noise level can exceed 

80 dB(A).

Wear ear protectors!

10. Accessories

11. Repairs

12. Environmental Protection

13. Technical Specifications