Пылесос VITEK VT-1830 SR - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
5
ENGLISH
turn off the vacuum cleaner immediately
after you are done using it.
Carpet/floor brush (20)
Set the switch on the brush to the desired posi-
tion (depending on the type of the surface you
wish to clean).
Attachment for furniture surface
(21)
Attachment is intended to clean fabric surface of
upholstered furniture.
Small brush (22)
The brush is intended to collect dust from the
surface of the furniture, presence of pile pre-
vents polished surface of the furniture from
damages.
Crevice attachment (23)
The attachment is intended for cleaning of ra-
diators, crevices, corners and between sofa pil-
lows.
USAGE INSTRUCTIONS
Attention!
The vacuum cleaner with a water filter is
intended only for dry cleaning; do not use
the unit to pick up water or any other liq-
uids.
- Before using the vacuum cleaner, pull the
power cord out to the desired length and in-
sert the plug into an outlet.
- Red mark on the power cord warns you about
the maximal power cord length.
- Never pull the power cord past the red mark.
Attention!
Always turn on the vacuum cleaner only
with the installed container for dust and
rubbish (5) filled with water and with the
installed
: air separator (12), suction
pipe (11), and there are should always
be installed НЕРА-filter (9) and the con-
tainer (10) on the vacuum cleaner output.
Always check whether the removable de-
tails are installed properly or not.
To turn on the vacuum cleaner press the On/
•
Off button
(4) (pic.7).
During operation you can adjust suction
•
power using the suction control
(17), situated
on the flexible hose handle (16).
After the cleaning is over, press the On/
•
Off button (4) and take the plug out of the
socket
.
Press the power cord-winding button
•
(1),
and hold the winding cord with your hand to
prevent entanglement and damage (pic.8).
Service
When water in the container (5) becomes dirty
•
(suction power can be reduced), you should
pour out it, to proceed with cleaning, fill the
bin with clear water, refer to the “Cleaning of
the container for dust and rubbish” section.
Note: It is recommended to pour out dirty
water from the container (5) and wash the
container and the removable parts after
each usage.
Before removing the container (5) it is
•
necessary to switch the unit with the switch
(4), and then take the plug out of the socket.
Cleaning the vacuum cleaner
Cleaning the container for dust and rubbish
Before removing the container (5) switch off
•
the unit with the switch (4), and take the plug
out of the socket.
Holding the plug (6) remove the container
•
from the body of the unit (pic.1).
Open the container lid (14), and then remove
•
the suction pipe (11) and the air separator
(12) from the container (pic.2, 3).
Pour put dirty water and wash the container
•
(5), the separator (12) and the suction pipe
(11) with water.
Fill the container (5) with water till the MAX
•
mark (pic.4).
Note:
Necessary quantity of water is
1200 ml.
Set the air separator on its place (12) (pic.3),
•
set the air intensity supply valve (13) to the
necessary position (pic.10, 11) and set the
suction pipe (11) (pic.2).
Close the container with the lid (14) (pic.6).
•
Set the container for dust and rubbish (5) on
•
the body (pic.1).
VT-1830 SR.indd 5
VT-1830 SR.indd 5
02.08.2011 9:41:37
02.08.2011 9:41:37
