VITEK VT-1830 SR - Инструкция по эксплуатации - Страница 4

4

 ENGLISH

-  if there is no water in the 

container for dust 

and rubbish

;

-   if the air separator and suction pipe are not 

installed in the container;

-  if the container with the НЕРА-filter is not in-

stalled.
Check the power cord and the power plug for 

• 

damages regularly. If there are some dam-
ages in the power cord, the power plug, or if 
the unit malfunctions, apply to the authorized 
service center.
The unit is intended for household usage only; 

• 

commercial usage of the vacuum cleaner is 
prohibited.

STORE THE INSTRUCTIONS IN A CONVENIENT 
PLACE

SAFETY PRECAUTIONS

Do not use the vacuum cleaner in the imme-

• 

diate vicinity of very hot surfaces, next to ash 
trays, or where flammable liquids are stored.
Before beginning to clean, remove sharp ob-

• 

jects from the floor to avoid damage of the fil-
ters.
If suction power decreases abruptly while 

• 

cleaning, immediately turn off the vacuum 
cleaner and check the telescoping tube or 
flexible hose for foreign objects. Turn off the 
vacuum cleaner, and then unplug it from the 
power outlet. Clear the obstruction and only 
then proceed with cleaning.

Assembling the vacuum cleaner

Before turning on the vacuum cleaner, make 
sure that the voltage of the mains corresponds 
to the voltage of the vacuum cleaner.

Always turn off the vacuum cleaner and unplug it 
from the outlet before changing the brushes/at-
tachments, and before performing maintenance 
on it.

Filling the container for dust and rubbish 
with water

Take the handle (6) remove the container (5) 

• 

from the body of the vacuum cleaner (pic.1).
Remove the container lid (14), remove the 

• 

suction pipe (11) and the air separator (12) 
from the container (5) (pic.2, 3).
Fill the container (5) with tapping water till the 

• 

MAX mark (pic.4).

Note: Necessary quantity of water is 1200 ml.

Put the air separator on its place (12).

• 

Open the air intensity supply valve (13) and 

• 

set the suction pipe (11) above it (pic.11).

Note: In the open position of the valve (13) 

(pic.11), two air flows, which more inten-
sively divide water into small drops form 
in the container (5), and the smaller the 
drops are, the more effective is suction of 
small dust

.

Close the container with the lid (14) (pic.5). 

• 

Set the container for dust and rubbish on the 

• 

body of the unit.

Attaching and removing the flexible hose

Insert the end of the flexible hose (18) in the 

• 

air inlet (7). 
To remove the flexible hose end (18) it is de-

• 

sirable to turn it slightly (pic.6).

Attaching the extension pipe and the attach-
ments

Attach the telescoping extension pipe (8) to 

• 

the flexible hose handle (16). 
Extend the lower part of the telescoping pipe 

• 

to the desired length by pressing the locking 
button.
Select the desired attachment: turbo brush 

• 

(19), carpet/floor brush (20) small brush 
(22), crevice attachment (23), attachment for 
furniture surface (21) and connect it to the 
telescoping extension pipe (8).

Turbo-brush (19)

The turbo brush (19) can be used to clean floors, 
rugs and carpets with long or short pile, and is 
ideal for picking up animal fur. The cylindrical 
brush with hard bristles rotates under the ac-
tion of the air current and its bristles effectively 
remove animal fur and loose carpet and rug fi-
bers.

Note: Never use the turbo brush to clean 

rugs with fringe and pile of 15 mm or 
more, because the rotating brush can 
cause damage to such rugs. Do not run 
the turbo brush over power cords and 

4

              ENGLISH         

VT-1830  SR.indd   4

VT-1830  SR.indd   4

02.08.2011   9:41:37

02.08.2011   9:41:37