Whirlpool ADP 321 WH - Инструкция по эксплуатации - Страница 22

22

Notes: 

Optimum performance levels when using the “Rapid” cycles can 
be achieved by respecting the specified number of place settings.

To reduce consumption even further, only run the dishwasher 
when it is full.

Note for Test Laboratories: 

for  information  on  comparative  EN 

testing conditions, please send an email to the following address: 
contact@whirlpool.com

Special wash cycles 

and Options

Half Load option/Child lock

If there are not many dishes to be washed, a half load 
cycle may be used in order to save water, electricity and 

detergent. Select the wash cycle and press the HALF LOAD 
button: the indicator light will illuminate. 

Press the HALF LOAD button to deselect this option.

Remember to halve the amount of detergent. 

Child lock

A long press of HALF LOAD button, will activate the CHILD 

LOCK  function.  The  CHILD  LOCK  function  will  block  the  control 
panel. To deactivate the CHILD LOCK, long press again.

Sani Rinse option/Tab

This option allows higher temperatures to be used. Select 
the washing program, press the SANI RINSE button and 

the indicator light will switch on. To deselect the option, press the 
same button again. 
Ideal to clean crockery and feeding bottles. 

Warning:

 the crockery and plates could be extremely hot at the 

end of the cycle.

The

 SANI RINSE option results in lengthening of the wash cycle.

Tablet

option

(Tab)

A long press of Sani rinse button, will activate the TAB 
function. This option optimises washing and drying results. 

To deactivate the TAB option, long press again.

The TAB option results in a longer wash cycle.

Drain out  

To  stop  and  cancel  the  active  cycle,  the  DRAIN  OUT 

function can be used.
A  long  press  of  START/PAUSE  button,  will  activate  the  DRAIN 
OUT function. The active cycle will be stopped and the water in 
the dishwasher will be drained out.

Wash options 

The OPTIONS may only be set, changed or reset after the wash 
cycle has been selected and before the Start/Pause button 
has been pressed.

Only the options which are compatible with the type of wash cycle 
set may be selected. If an option is not compatible with the selected 
wash cycle 

(see  Table  of  wash  cycles)

,  the  corresponding  led/

symbol flashes rapidly 3 times.

If an option is selected which is not compatible with another 
(previously  selected)  option,  it  will  flash  3  times  and  switch  off, 
while the most recently selected option will remain active.
To deselect an option which has been set by mistake, press the 
corresponding button again. 

Delayed start

The start of the program may be delayed for 
a period of time between 

0:30

 and 

24

 hours.

1. Select the program and any desired options. Press the 
DELAYED START button (repeatedly) to delay the start of the 
program. Adjustable from 0:30 to 24 hours. 
With each press of the button, the delay start increases 
by:  0:30  if  selection  below  4  hours,  1:00  if  selection  is  be-
low 12 hours, 4 hours if selection is above 12 hours. If 24 
hours reached, and the button is pressed, the delayed start is 
deactivated.
2.  Press  the  START/PAUSE  button:  the  timer  will  begin 
counting down;
3. Once this time has elapsed, the indicator light switches 
off and the program begins automatically. If at the time of 
the countdown the START/PAUSE button is pressed again the 
DELAYED  START option is cancelled and the selected pro-
gram starts automatically.

The Start Delay function cannot be set once a wash cycle 

has started.