Worx SAW WX527 - Инструкция по эксплуатации - Страница 9

Lithium-Ion Cordless Circular Saw EN

9

operating procedures or conditions and can be 

avoided by taking proper precautions as given below.

a)  Maintain a firm grip on the saw and position 

your arms to resist kickback forces. 

Position your body to either side of the 

blade, but not in line with the blade. 

Kickback 

could cause the saw to jump backwards, but 

kickback forces can be controlled by the operator, 

if proper precautions are taken.

b)  When blade is binding, or when interrupting 

a cut for any reason, release the trigger and 

hold the saw motionless in the material until 

the blade comes to a complete stop. Never 

attempt to remove the saw from the work 

or pull the saw backward while the blade is 

in motion or kickback may occur. 

Investigate 

and take corrective actions to eliminate the cause 

of blade binding.

c)  When restarting a saw in the workpiece, 

center the saw blade in the kerf and check 

that saw teeth are not engaged into the 

material. 

If saw blade is binding, it may walk 

up or kickback from the workpiece as the saw is 

restarted.

d) Support large panels to minimize the risk of 

blade pinching and kickback. 

Large panels 

tend to sag under their own weight. Supports 

must be placed under the panel on both sides, 

near the line of cut and near the edge of the 

panel.

e)  Do not use dull or damaged blades. 

Unsharpened or improperly set blades produce 

narrow kerf causing excessive friction, blade 

binding and kickback.

f)   Blade depth and bevel adjusting locking 

levers must be tight and secure before 

making cut. 

If blade adjustment shifts while 

cutting, it may cause binding and kickback.

g)  Use extra caution when sawing into existing 

walls or other blind areas. 

The protruding 

blade may cut objects that can cause kickback.

SAFETY INSTRUCTIONS 

FOR PLUNGE TYPE SAW

Guard function

a)  Check guard for proper closing before 

each use. Do not operate the saw if guard 

does not move freely and enclose the 

blade instantly. Never clamp or tie the 

guard so that the blade is exposed. 

If saw is 

accidentally dropped, guard may be bent. Check 

to make sure that guard moves freely and does 

not touch the blade or any other part, in all angles 

and depths of cut.

b)  Check the operation and condition of the 

guard return spring. If the guard and the 

spring are not operating properly, they 

must be serviced before use. 

Guard may 

operate sluggishly due to damaged parts, gummy

deposits, or a build-up of debris.

c)  Assure that the base plate of the saw will not 

shift while performing the “plunge cut” when 

the blade bevel setting is not at 90°. 

Blade 

shifting sideways will cause binding and likely kick 

back.

d)  Always observe that the guard is covering 

the blade before placing saw down on 

bench or floor. 

An unprotected, coasting blade 

will cause the saw to walk backwards, cutting 

whatever is in its path. Be aware of the time it 

takes for the blade to stop after switch is released.

ADDITIONAL SAFETY 

RULES FOR YOUR 

CIRCULAR SAW

1.   Use only saw blades recommended by the 

manufacturer, which conform to EN 847-1, if 

intended for wood and analogous materials.

2.   Do not use any abrasive wheels.

3.   Use only blade diameter(s) in accordance with the 

markings.

4.   Identify the correct saw blade to be used for the 

material to be cut.

5.   Use only saw blades that are marked with a speed 

equal or higher than the speed marked on the 

tool.

SAFETY INSTRUCTIONS 

FOR BATTERY PACK

a)   Do not dismantle, open or shred cells 

or battery pack.

b)   Do not short-circuit a battery pack. Do not 

store battery packs haphazardly in a box or 

drawer where they may short-circuit each 

other or be short-circuited by conductive 

materials.

 When battery pack is not in use, keep 

it away from other metal objects, like paper 

clips, coins, keys, nails, screws or other small 

metal objects, that can make a connection from 

one terminal to another. Shorting the battery 

terminals together may cause burns or a fire.

c)   Do not expose battery pack to heat or fire. 

Avoid storage in direct sunlight.

d)   Do not subject battery pack to mechanical 

shock.

e)   In the event of battery leaking, do not 

allow the liquid to come into contact 

with the skin or eyes. If contact has been 

made, wash the affected area with copious 

amounts of water and seek medical advice.

f)   Seek medical advice immediately if a cell or 

battery pack has been swallowed.

g)   Keep battery pack clean and dry.

h)   Wipe the battery pack terminals with a 

clean dry cloth if they become dirty.