Makita DCS553Z - Инструкция по эксплуатации - Страница 7

Пилы дисковые Makita DCS553Z - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.

Если остались вопросы, задайте их в комментариях после инструкции.

"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
Страница:
/ 72
Загружаем инструкцию
background image

7 ENGLISH

5. 

To check lower guard, open lower guard by 

hand, then release and watch guard closure. 

Also check to see that retracting handle does 

not touch tool housing.

 Leaving blade exposed 

is VERY DANGEROUS and can lead to serious 

personal injury.

Additional safety warnings

1. 

Do not stop the blades by lateral pressure on 

the saw blade.

2. 

DANGER: 

Do not attempt to remove cut material when 

blade is moving.

 

CAUTION: Blades coast after turn off.

3. 

Place the wider portion of the saw base on 

that part of the workpiece which is solidly 

supported, not on the section that will fall off 

when the cut is made. If the workpiece is short 

or small, clamp it down. DO NOT TRY TO HOLD 

SHORT PIECES BY HAND!

4. 

Never attempt to make a cut with the tool held 

upside down in a vise. This is extremely dan

-

gerous and can lead to serious accidents.

5. 

Wear safety goggles and hearing protection 

during operation.

6. 

Do not use any abrasive wheels.

7. 

Only use the saw blade with the diameter that 

is marked on the tool or specified in the man

-

ual.

 Use of an incorrectly sized blade may affect 

the proper guarding of the blade or guard opera-

tion which could result in serious personal injury.

8. 

Always use the saw blade intended for cutting 

the material that you are going to cut.

9. 

Only use the saw blades that are marked with 

a speed equal or higher than the speed marked 

on the tool.

SAVE THESE INSTRUCTIONS.

WARNING:

 

DO NOT let comfort or familiarity 

with product (gained from repeated use) replace 

strict adherence to safety rules for the subject 

product. MISUSE or failure to follow the safety 

rules stated in this instruction manual may cause 

serious personal injury.

Important safety instructions for 

battery cartridge

1. 

Before using battery cartridge, read all instruc

-

tions and cautionary markings on (1) battery 

charger, (2) battery, and (3) product using 

battery.

2. 

Do not disassemble battery cartridge.

3. 

If operating time has become excessively 

shorter, stop operating immediately. It may 

result in a risk of overheating, possible burns 

and even an explosion.

4. 

If electrolyte gets into your eyes, rinse them 

out with clear water and seek medical atten-

tion right away. It may result in loss of your 

eyesight.

5. 

Do not short the battery cartridge:

(1) 

Do not touch the terminals with any con

-

ductive material.

(2) 

Avoid storing battery cartridge in a con

-

tainer with other metal objects such as 

nails, coins, etc.

(3) 

Do not expose battery cartridge to water 

or rain.

A battery short can cause a large current 

flow, overheating, possible burns and even a 

breakdown.

6. 

Do not store the tool and battery cartridge in 

locations where the temperature may reach or 

exceed 50 °C (122 °F).

7. 

Do not incinerate the battery cartridge even if 

it is severely damaged or is completely worn 

out. The battery cartridge can explode in a fire.

8. 

Be careful not to drop or strike battery.

9. 

Do not use a damaged battery.

10. 

The contained lithium-ion batteries are subject 

to the Dangerous Goods Legislation require-

ments. 

For commercial transports e.g. by third parties, 

forwarding agents, special requirement on pack-

aging and labeling must be observed. 

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required. 

Please also observe possibly more detailed 

national regulations. 

Tape or mask off open contacts and pack up the 

battery in such a manner that it cannot move 

around in the packaging.

11. 

Follow your local regulations relating to dis

-

posal of battery.

12. 

Use the batteries only with the products 

specified by Makita.

 Installing the batteries to 

non-compliant products may result in a fire, exces

-

sive heat, explosion, or leak of electrolyte.

SAVE THESE INSTRUCTIONS.

CAUTION:

 

Only use genuine Makita batteries.

 

Use of non-genuine Makita batteries, or batteries that 

have been altered, may result in the battery bursting 

causing fires, personal injury and damage. It will 

also void the Makita warranty for the Makita tool and 

charger.

Tips for maintaining maximum 

battery life

1. 

Charge the battery cartridge before completely 

discharged. Always stop tool operation and 

charge the battery cartridge when you notice 

less tool power.

2. 

Never recharge a fully charged battery car

-

tridge. Overcharging shortens the battery 

service life.

3. 

Charge the battery cartridge with room tem

-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let 

a hot battery cartridge cool down before 

charging it.

4. 

Charge the battery cartridge if you do not use 

it for a long period (more than six months). 

Характеристики

Оцените статью
tehnopanorama.ru
Остались вопросы?

Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)

Задать вопрос

Часто задаваемые вопросы
Как посмотреть инструкцию к Makita DCS553Z?
Необходимо подождать полной загрузки инструкции в сером окне на данной странице
Руководство на русском языке?
Все наши руководства представлены на русском языке или схематично, поэтому вы без труда сможете разобраться с вашей моделью
Как скопировать текст из PDF?
Чтобы скопировать текст со страницы инструкции воспользуйтесь вкладкой "HTML"