AEG KS 12-1 - Инструкция по эксплуатации - Страница 21

Deutsch

19

English

GB

b)  When blade is binding, or when interrupting a cut for 

any reason, release the trigger and hold the saw motionless 

in the material until the blade comes to a complete stop. 

Never attempt to remove the saw from the work or pull the 

saw backward while the blade is in motion or kickback may 

occur.

Investigate and take corrective actions to eliminate the cause 

of blade binding.

c)  When restarting a saw in the workpiece, centre the saw 

blade in the kerf so that the saw teeth are not engaged into 

the material. 

If a saw blade binds, it may walk up or kickback from 

the workpiece as the saw is restarted.

d)  Support large panels to minimise the risk of blade 

pinching and kickback.

Large panels tend to sag under their own 

weight. Supports must be placed under the panel on both sides, 

near the line of cut and near the edge of the panel.

e)  Do not use dull or damaged blades. 

Unsharpened or im-

properly set blades produce narrow kerf causing excessive friction, 

blade binding and kickback.

f)  Blade depth and bevel adjusting locking levers must be 

tight and secure before making the cut. 

If blade adjustment 

shifts while cutting, it may cause binding and kickback.

g)  Use extra caution when sawing into existing walls or 

other blind areas. 

The protruding blade may cut objects that can 

cause kickback.

Lower guard function
a)  Check the lower guard for proper closing before each use. Do 

not operate the saw if the lower guard does not move freely and 

close instantly. Never clamp or tie the lower guard into the open 

position.  

If the saw is accidentally dropped, the lower guard may 

be bent. Raise the lower guard with the retracting handle and make 

sure it moves freely and does not touch the blade or any other part, 

in all angles and depths of cut.

b)  Check the operation of the lower guard spring. If the 

guard and the spring are not operating properly, they must 

be serviced before use. 

Lower guard may operate sluggishly due 

to damaged parts, gummy deposits, or a build-up of debris.

c)  The lower guard may be retracted manually only for 

special cuts such as „plunge cuts“ and „compound cuts“. 

Raise the lower guard by the retracting handle and as soon 

as the blade enters the material, the lower guard must be 

released. 

For all other sawing, the lower guard should operate 

automatically.

d)  Always observe that the lower guard is covering the 

blade before placing the saw down on bench or floor. 

An 

unprotected, coasting blade will cause the saw to walk backwards, 

cutting whatever is in its path. Be aware of the time it takes for the 

blade to stop after switch is released.

Additional Safety and Working Instructions

Wear ear protectors. Exposure to noise can cause hearing loss.
Use protective equipment. Always wear safety glasses when 

working with the machine. The use of protective clothing is re-

commended, such as dust mask, protective gloves, sturdy non-slip 

footwear, helmet and ear defenders.

The dust produced when using this tool may be harmful to health. 

Do not inhale the dust.  Use a dust absorption system and wear a 

suitable dust protection mask. Remove deposited dust thoroughly, 

e.g. with a vacuum cleaner.
Do not use saw blades not corresponding to the key data given in 

these instructions for use.
It is necessary to select a saw blade which is suitable for the 

material being cut.
Use only woodworking blades specified in this manual, which 

comply with EN 847-1.
The rated speed of the accessory must be at least equal to the 

maximum speed marked on the power tool.
Do not fix the on/off switch in the „on“ position when using the saw 

hand-held.
Do not use abrasion discs in this machine!

WORKING INSTRUC TIONS

Adapt the feed speed to avoid overheating the blade tips.

SPECIFIED CONDITIONS OF USE

This electronic circular saw can cut lengthways and mitre accura-

tely in wood.

MAINS CONNEC TION

Connect only to single-phase AC system voltage as indicated on 

the rating plate. It is also possible to connect to sockets without an 

earthing contact as the design conforms to safety class II. 

Appliances used at many different locations including wet room 

and open air must be connected via a residual current device (FI, 

RCD, PRCD) of 30mA or less.
Always disconnect the plug from the socket before carrying out any 

work on the machine.
Keep mains lead clear from working range of the machine. Always 

lead the cable away behind you.
Before use check machine, cable, and plug for any damages or 

material fatigue. Repairs should only be carried out by authorised 

Service Agents.

MAINTENANCE

Always disconnect the plug from the socket before carrying out any 

work on the machine.
If the replacement of the supply cord is necessary, this has to be 

done by the manufacturer or his agent in order to avoid a safety 

hazard.
Be sure to disconnect the tool from the power supply before 

attaching or removing the saw blade.
Clean tool and guarding system with dry cloth.
Certain cleaning agents and solvents are harmful to plastics and 

other insulated parts.
Keep the apparatus handle clean, dry and free of spilt oil or grease.
Check the function of guards.
Regular maintenance and cleaning provide for a long service life 

and safe handling.
The ventilation slots of the machine must be kept clear at all times.
Remove dust regularly. Remove the sawdust which has accummu-

lated inside the saw in order to avoid the risk of fire.