Makita DHR263Z - Инструкция по эксплуатации - Страница 5

5 

Work mode: drilling into metal 
Vibration emission (a

h,D

) : 5.0 m/s

2 

Uncertainty (K) : 1.5 m/s

2 

ENG901-1 

• 

The declared vibration emission value has been 
measured in accordance with the standard test 
method and may be used for comparing one tool 
with another. 

• 

The declared vibration emission value may also be 
used in a preliminary assessment of exposure. 

WARNING: 

• 

The vibration emission during actual use of the 
power tool can differ from the declared emission 
value depending on the ways in which the tool is 
used. 

• 

Be sure to identify safety measures to protect the 
operator that are based on an estimation of 
exposure in the actual conditions of use (taking 
account of all parts of the operating cycle such as 
the times when the tool is switched off and when it 
is running idle in addition to the trigger time). 
 

ENH101-16 

For European countries only 

EC Declaration of Conformity 

We Makita Corporation as the responsible manufacturer 
declare that the following Makita machine(s): 

Designation of Machine:   
Cordless Combination Hammer 
Model No./ Type: DHR263, DHR264 
are of series production and 

Conforms to the following European Directives: 

2006/42/EC 

And are manufactured in accordance with the following 
standards or standardised documents: 

EN60745 

The technical documentation is kept by:   

Makita International Europe Ltd. 
Technical Department, 
Michigan Drive, Tongwell, 
Milton Keynes, Bucks MK15 8JD, England 
 

18.6.2013

000230 

Tomoyasu Kato 

Director 

Makita Corporation 

3-11-8, Sumiyoshi-cho, 

Anjo, Aichi, 446-8502, JAPAN 

GEA010-1 

General Power Tool Safety 
Warnings 

WARNING Read all safety warnings and all 

instructions.

 Failure to follow the warnings and 

instructions may result in electric shock, fire and/or 
serious injury. 

Save all warnings and instructions for 

future reference. 

GEB046-2 

CORDLESS ROTARY HAMMER 
SAFETY WARNINGS 

1. 

Wear ear protectors.

 Exposure to noise can 

cause hearing loss. 

2. 

Use auxiliary handle(s), if supplied with the 
tool.

 Loss of control can cause personal injury. 

3. 

Hold power tool by insulated gripping 
surfaces, when performing an operation 
where the cutting accessory may contact 
hidden wiring.

 Cutting accessory contacting a 

"live" wire may make exposed metal parts of the 
power tool "live" and could give the operator an 
electric shock. 

4. 

Wear a hard hat (safety helmet), safety 
glasses and/or face shield. Ordinary eye or 
sun glasses are NOT safety glasses. It is also 
highly recommended that you wear a dust 
mask and thickly padded gloves. 

5. 

Be sure the bit is secured in place before 
operation. 

6. 

Under normal operation, the tool is designed 
to produce vibration. The screws can come 
loose easily, causing a breakdown or accident. 
Check tightness of screws carefully before 
operation. 

7. 

In cold weather or when the tool has not been 
used for a long time, let the tool warm up for a 
while by operating it under no load. This will 
loosen up the lubrication. Without proper 
warm-up, hammering operation is difficult. 

8. 

Always be sure you have a firm footing. 
Be sure no one is below when using the tool 
in high locations. 

9. 

Hold the tool firmly with both hands. 

10. 

Keep hands away from moving parts. 

11. 

Do not leave the tool running. Operate the tool 
only when hand-held. 

12. 

Do not point the tool at any one in the area 
when operating. The bit could fly out and 
injure someone seriously. 

13. 

Do not touch the bit or parts close to the bit 
immediately after operation; they may be 
extremely hot and could burn your skin.