Hitachi DH24PH-NY - Инструкция по эксплуатации - Страница 16

16

English

3. Dismounting (Fig. 21)

Remove the core bit shank from the rotary hammer
and strike the head of the core bit shank strongly two
or three times with a hammer holding the core bit,
then the thread becomes loose and the core bit can
be removed.

LUBRICATION

Low viscosity grease is applied to this rotary hammer so
that it can be used for a long period without replacing
the grease. Replace the grease whenever you change
the carbon brush to maintain the service life.
Further use of the rotary hammer with lock off grease
will cause the machine to seize up reduce the service life.

CAUTION

A special grease is used with this machine, therefore,
the normal performance of the machine may be badly
affected by use of other grease. Please be sure to let
one of our service agents undertake replacement of
the grease.

MAINTENANCE AND INSPECTION

1. Inspecting the drill bits

S i n c e   u s e   o f   a   d u l l   t o o l   w i l l   c a u s e   m o t o r
malfunctioning and degraded efficiency, replace the
drill bit with new ones or resharpen them without
delay when abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very ”heart” of the
power tool. Exercise due care to ensure the winding
does not become damaged and/or wet with oil or
water.

4. Inspecting the carbon brushes

For your continued safety and electrical shock
protection, carbon brush inspection and replacement
on this tool should ONLY be performed by a HITACHI
Authorized Service Center.

5. Replacing supply cord

If the supply cord of Tool is damaged, the Tool must
be returned to a Hitachi Authorized Service Center
for the cord to be replaced.

6. Service parts list
CAUTION

Repair, modification and inspection of Hitachi Power
Tools must be carried out by a Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts may be changed without
prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with
statutory/country specific regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling
instruction, to a Hitachi Authorized Service Center.

NOTE

Due to HITACHI’s continuing program of research and
development, the specifications herein are subject to
change without prior notice.

Information concerning airborne noise and vibration

The measured values were determined according to
EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level:

100 dB (A) (DH24PH)
101 dB (A) (DH26PC)
100 dB (A) (DH28PCY)

Measured A-weighted sound pressure level:

89 dB (A) (DH24PH)
90 dB (A) (DH26PC)
89 dB (A) (DH28PCY)

Uncertainty KpA: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined
according to EN60745.

Hammer drilling into concrete:
Vibration emission value 

a

h,

HD

 = 15.3 m/s

2

 (DH24PH)

14.8 m/s

2

 (DH26PC)

11.5 m/s

2

 (DH28PCY)

Uncertainty K = 1.6 m/s

2 

 (DH24PH)

1.5 m/s

2 

 (DH26PC, DH28PCY)

Equivalent chiselling value:
Vibration emission value 

a

h,

CHeq

 = 12.1 m/s

2

 (DH24PH)

11.0 m/s

2

 (DH26PC)

10.5 m/s

2

 (DH28PCY)

Uncertainty K = 1.5 m/s

2

The declared vibration total value has been measured in
accordance with a standard test method and may be
used for comparing one tool with another.
It may also be used in a preliminary assessment of
exposure.

WARNING

䡬

The vibration emission during actual use of the power
tool can differ from the declared total value depending
on the ways in which the tool is used.

䡬

Identify safety measures to protect the operator that
are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger time).