Elitech ТП 15Г - Инструкция по эксплуатации - Страница 17

16

power supply (danger of deep discharg-

ing).

- A new battery pack or a battery pack not 

used for a longer period of time reaches 

it full capacity after about 5 charging and 

discharging cycles.

- Battery packs should, before charging, be 

fully discharged if possible. 

  Continuous starting of the charging process 

shortens the lifespan of the batteries.

- A considerably reduced time of operation 

per charging shows that the battery pack is 

used up an should be replaced by a new one.

- NiCd battery packs that are not used for 

longer periods should be stored in a dis-

charged state.

Special instructions for NiMH battery 
packs:

- The output of NiMH battery packs drops 

noticeably at ambient temperatures below 

0° C or above 45° C.

- Do not overload the tool (do not load the 

tool excessively so that it comes to a stand-

still).

- Even if NiMH battery packs are not used, 

recharge them approx. every 4 months so 

that they retain their full capacity.

- NiMH battery packs should be left for 60 

min. in the charger after every 10th fast 

charge to compensate any differences in 

capacity between the cells.

- Because NiMH battery packs discharge 

auto-matically, store them preferably at 

ambient temperatures of between 0° C and 

25° C.

7  

Recycling battery packs 

Never throw spent battery packs 
into domestic waste containers! 

Return spent or defective battery packs 

to dealers, the Festool after-sales service 

department or approved waste disposal fa-

cilities. This ensures that they are correctly 

recycled.

8  

Warranty 

Our equipment is under warranty for at 

least 12 months with regard to material or 

production faults in accordance with national 

legislation. In the EU countries, the warranty 

period is 24 months (an invoice or delivery 

note is required as proof of purchase). Dam-

age resulting from, in particular, normal wear 

and tear, o-verloading, improper handling, or 

caused by the user or other damage caused 

by not following the operating instructions, 

or any fault acknowledged at the time of 

purchase, is not covered by the warranty. 

Damage caused by the use of non-original 

accessories and consumable material (e.g. 

sanding pads) is also excluded. Complaints 

will only be acknowledged if the equipment 

has not been dismantled before being sent 

back to the suppliers or to an authorised 

Festool customer support workshop. Store 

the operating instructions, safety notes, 

spare parts list and proof of purchase in a 

safe place. In addition, the manufacturer‘s 

current warranty conditions apply. 

Note

We reserve the right to make changes to 

the technical data contained in this infor-

mation as a result of ongoing research and 

development work.

9 

EU Declaration of Conformity

Cordless drill/

screwdriver 

Serial no.

C12

490454

Year of CE mark: 2005

We declare under sole responsibility that this 

product complies with the following norms 

or normative documents: EN 60745-1, EN 

60745-2-1, EN 60745-2-2, EN 55014-1 

in accordance with the regulations stipu-

lated in Directive 98/37/EC (until 28 Dec. 

2009), 2006/42/EC (from 29 Dec. 2009), 

2004/108/EC.

Charger

Serial no.

LC 45

491573, 491815

Year of CE mark: 2003

We declare under sole responsibility that this 

product complies with the following norms 

or normative documents: EN 60335-1, EN 

60335-2-29, EN 61000-3-2, EN 61000-3-3, 

EN 61204-3 in accordance with the regula-

tions stipulated in Directive 2004/108/EC, 

2006/95/EC.

Dr. Johannes Steimel

Head of research and development

Festool GmbH, Wendlingen, Germany