Einhell GC-SP 3580 LL - Инструкция по эксплуатации - Страница 18

GB

- 18 -

The maximum 

fl

 ow rate is reduced by the non-

return valve (5) on the hose connection.

Flexible hose lines must be fastened to the hose 

adapter with a hose clip (not included in the 

scope of supply).

When installing, never hang the equipment by the 

discharge line or by the power cable. The equip-

ment must be hung up with the provided carry 

handle or it must rest on the bottom of the shaft. 

To ensure that the equipment works properly, the 

bottom of the shaft always must be free of sludge 

and other accumulations of dirt. If the water level 

is too low, the sludge in the shaft can quickly dry 

out and hinder the equipment from starting. It is 

necessary therefore to check the equipment regu-

larly (carry out trial start-ups).

The pump shaft should be large enough.

5.2 Mains connection

Danger!

The equipment you have purchased comes with 

an earthing-pin plug. The equipment is designed 

for connection to a socket outlet with earthing 

contact for 230 V ~ 50 Hz. Make sure that the 

socket-outlet is su

ffi

  ciently fused (at least 6 A) 

and in good working order. Insert the power plug 

in the socket-outlet and the equipment is ready 

for operation.

Danger!

To rule out danger, this work must be left strictly to 

a specialist electrician or Customer Service.

6. Operation

 You can put the equipment into operation after 

you have thoroughly read the installation and ope-

rating instructions. Pay attention to the following 

points:

• 

 Make sure that the equipment is set up secu-

rely.

• 

 Check that the discharge line is fitted correct-

ly.

• 

 Make sure that the electrical connection is 

230 V ~ 50 Hz.

• 

 Check that the electrical socket-outlet is in 

good working order.

• 

 Make sure that no moisture or water can ever 

reach the power connection.

• 

 Make sure that the equipment does not run 

dry.

• 

 To switch off the equipment, pull the power 

plug out of the socket outlet.

 Setting the On/O

ff

  switching point:

The ON/OFF switching point of the 

fl

 oating switch 

can be adjusted by shifting the 

fl

 oating switch in 

the 

fl

 oating switch notched holder (Fig. 4/Item 6).

• 

 The floating switch must be fitted so that the 

switching point height: ON and the switch 

point height: OFF can be reached easily and 

with little force. Check this by placing the 

equipment in a container filled with water 

and carefully raising and lowering the floating 

switch with your hand. You can then see whe-

ther the equipment switches on and off.

• 

 Make sure that the distance between the floa-

ting switch head and the cable holder is not 

too smaller than 10 cm. If the distance is too 

small, there is no guarantee that the equip-

ment will work correctly.

• 

 When adjusting the floating switch, make 

sure that the floating switch does not touch 

the bottom before the equipment is switched 

off. Important! Risk of dry running.

Manual mode/shallow water:

To operate manually or in shallow water, 

fi

 t the 

fl

 oat switch as shown in Fig. 1. The equipment will 

then run continuously. In shallow suction mode, 

water can be sucked up down to a level of 1 mm. 

To prevent dry running, this operating mode is 

allowed only under supervision. The equipment 

must be switched o

ff

  (pull out the power plug) 

as soon as no more water is emitted from the 

discharge line.

Please note:

For the equipment to suck up water in shallow 

suction mode there must be a minimum depth of 

8 mm of water.

7.  Replacing the power cable

Danger!

If the power cable for this equipment is damaged, 

it must be replaced by the manufacturer or its 

after-sales service or similarly trained personnel 

to avoid danger.

Anl_GC_SP_3580_LL_SPK7.indb   18

Anl_GC_SP_3580_LL_SPK7.indb   18

02.08.2016   11:42:01

02.08.2016   11:42:01