Музыкальные центры Panasonic SC-AKX710GSK - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
Confidential
Until:
1 Aug 2018
19
T
Q
BJ
213
8
19
ENGLISH
D:\PSG\Amalina PSG job\AKX710 GS data\AKX710 GS TQBJ2138 EN.fm
“NO PLAY”
“UNSUPPORT”
•
There is no album or track in the USB device.
•
Examine the content. You can only play supported format.
•
The files in the USB device can be corrupted. Format the
USB device and try again.
•
The system may have a problem. Switch off the system and
then switch on again.
“NO TRACK”
•
There is no album or track in the internal memory.
“NOT SUPPORTED”
•
To use Karaoke effect in AUX source, set “AUX MODE” to
“MODE 1”.
“PLAYERROR”
•
An unsupported MP3 file has been played. The system will
skip that track and play the next one.
“REC ERROR”
•
You disconnected the USB device during recording.
Connect the USB device and do recording again.
•
An error occurred during USB recording. Disconnect the
USB device and then connect it again.
“REMOTE 1”
“REMOTE 2”
•
The remote control and the main unit are using different
codes. Change the code of the remote control.
–
When “REMOTE 1” is shown, press and hold [OK] and [1]
for a minimum of 4 seconds.
–
When “REMOTE 2” is shown, press and hold [OK] and [2]
for a minimum of 4 seconds.
“TEMP NG”
•
The temperature protection circuit has been activated, and
the system will switch off. Let the unit cool down before
switching it on again.
•
Check that the ventilation opening of the unit is not
obstructed.
•
Ensure this unit is well ventilated.
“TRK FULL”
•
The number of files has exceeded the supported limit.
“USB A NO DEVICE”
“USB B NO DEVICE”
•
The USB device is not connected. Examine the connection.
“USB OVER CURRENT ERROR”
•
The USB device is drawing too much power. Disconnect the
USB device, switch off the system and then switch on again.
•
Check the connection, it may be caused by a faulty USB
cable.
“VBR”
•
The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
Remote control code
When other Panasonic equipment responds to the remote
control of this system, change the remote control code for
this system.
Preparation
Press [SELECT <, >] repeatedly to select “AUX”.
█
To set the code to “REMOTE 2”
1
Press and hold [SELECT] on the main unit and [2]
on the remote control until “REMOTE 2” is shown.
2
Press and hold [OK] and [2] for a minimum of
4 seconds.
█
To set the code to “REMOTE 1”
1
Press and hold [SELECT] on the main unit and [1]
on the remote control until “REMOTE 1” is shown.
2
Press and hold [OK] and [1] for a minimum of
4 seconds.
System memory reset
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC mains lead.
2
While you press and hold [
1
] on the main unit,
connect the AC mains lead again.
Continue to press and hold the button until
“– – – – – – – – –” is shown.
3
Release [
1
].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
AKX710 GS TQBJ2138.book Page 19 Thursday, July 12, 2018 10:50 AM
offset printing
