Мойки высокого давления Lavor PRO ARIZONA 1311 LP с барабаном 8.665.0110 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
CAUTION: Make use only of liquid detergent, do not
absolutely use acid or too much alkaline products.
We suggest you to make use of our products, which
have been studied for the use with washer machines.
CARE AND MAINTENANCE
(vedi fig.
)
*.1035"/5 #FGPSF EPJOH BOZ XPSL
on the cleaner, discharge the pressure
and disconnect the electricity and water
supplies.
CHECKING THE PUMP OIL LEVEL
Check the oil level periodically. The oil must be
changed for the first time after 50 working hours,
with subsequent changes every 500 hours. SAE
20/30 , 15W-40, 20W-40 oil is recommended .
$)&$,*/(5)&8"5&3*/5",&'*-5&3
Inspect and clean the water intake filter on the inta-
ke union periodically. This is important to prevent
fouling which may impair operation of the pump.
$)&$,*/(5)&413":30%/0;;-&
Replace the nozzle when the pressure drops
below the normal values.
DESCALING
The descaling procedure must be carried out periodically
with specific products. The interval depends on the hard-
ness of the water. Pour one litre of product for every 15
litres of water into a drum containing at least 30 litres of
water. Disconnect the gun from the high pressure line and
place its free end in the drum, in order to form a closed cir-
cuit, and draw the solution into the machine for at least 10
minutes. The delivery end of the line should discharge into
a canvas or mesh bag so that the scale removed is not re-
turned to the circuit. Then restore the normal connection
and rinse with plenty of cold water. This operation should
be carried out by our after-sales service, since the descal-
ing product may cause wear of components. Comply with
the regulations in force when disposing of the descaling
agent.
ELECTRIC DIAGRAM
See illustrations,
.
8"5&3%*"(3".
See illustrations,
.
5306#-&4)005*/(
Before doing any work on the machine, disconnect
the electricity and water supplies and discharge the
pressure. Proceed systematically to identify Faults
following the chart below; if you are still unable to
eliminate the problem, call in the
"VUIPSJ[FE"GUFS
Sales Service
.
Fault
8IFO TXJUDIi0/w UIF NB
chine will not start work
ing
Cause
t
Plug not properly inserted in
socket.
t
Electric socket is faulty.
t
The main voltage is insuffi-
cient.
t
The pump is stuck.
t
Gauge of extension lead not
sufficient.
Repair
t
Fit plug in power socket cor-
rectly.
t
Have electrical socket
checked.
t
Have a check made on the
suitability of the mains system.
t
Turn switch to ON while keep-
ing nozzle trigger pressed; if
problem persists, contact an
authorised service centre.
Fault
The motor stops suddenly
Cause
t
Thermic safety switch has
tripped due to the overheating.
t
Cable extension seems to be
inadequate.
Repair
t
Leave motor to cool for a few
minutes. If the problem persists,
contact an authorised service
centre..
Fault
5IF QVNQ EPFTOU SFBDI
the necessary pressure
EN
20
