Karcher K 4 Full Control 1.324-000 - Инструкция по эксплуатации - Страница 13

– 7



Park the appliance on an even surface.



Insert the mains plug into the socket. 

For connection values, see type plate/technical data.

ATTENTION

Impurities in the water can damage the high-pressure 
pump and the accessories. For protection, the use of 
the KÄRCHER water filter (optional accessory, order 
no. 4.730-059) is recommended.

Observe regulations of water supplier.

ATTENTION

Hose couplings made of metal with aquastop can dam-
age the pump! Please use plastic couplings or KÄRCH-
ER brass couplings.

Illustration 



Screw the coupling element to the water connec-
tion on the appliance.



Attach the water supply hose to the coupling on the 
water connection.



Connect the water supply hose to the water supply.



Completely open the water tap.

This high-pressure cleaner is suited to work with the 
KÄRCHER suction hose with backflow valve (Optional 
accessory, order no. 2.643-100) to draw in surface wa-
ter, e.g. from water butts or ponds (see specifications for 
max. suction height). 

Note:

 With vacuuming operation, the coupling for the 

water connection is not required.



Fill the suction hose with water.



Screw the suction hose into the water connection of 
the appliance and insert it into the water source 
(e.g. rainwater drum).

Bleed the device as follows prior to operation:



Turn on the appliance “I/ON”.



Unlock the lever of the trigger gun.



Push the lever of the trigger gun, the device will 
switch on.



Let the device run (max. 2 minutes) until the water 
exits the trigger gun without bubbles.



Release the lever of the trigger gun.



Lock the lever of the trigger gun.

ATTENTION

Dry running of more than 2 minutes leads to damage of 
the high-pressure pump. If the appliance does not build 
up pressure within 2 minutes, switch the appliance off 
and proceed in accordance with the instructions in 
Chapter "Troubleshooting".

몇

CAUTION

Keep a distance of at least 30 cm when using the jet for 
cleaning painted surfaces to avoid damage.

ATTENTION

Car tyres, paint or sensitive surfaces such as wood 
should not be cleaned with the dirt blaster, as there is a 
risk of damage.



Select a spray lance suitable for the cleaning task.

Illustration 



Push the spray lance into the trigger gun and fasten 
it by a 90° rotation.



Turn on the appliance “I/ON”.



Unlock the lever of the trigger gun.



Push the lever of the trigger gun, the device will 
switch on.

Note:

 Release the lever of the trigger gun; the de-

vice will switch off again. High pressure remains in 
the system.

Full Control spray lance Vario Power 



Turn the spray lance until the LED of the required 
pressure level is on at the pressure indicator of the 
trigger gun.

The pressure indicator on the trigger gun shows the cur-
rently set pressure level during operation with a Full 
Control spray lance.

Note:

 The pressure indicator is not significant during 

operation with the T-Racer and other accessories.

ATTENTION

The sensitivity of the materials can strongly differ de-
pending on the age and the condition. The so-called 
recommendations are non-binding.

Start up

Water supply

Water supply from mains

Drawing in water from open reservoirs

Operation

High pressure operation

Full Control System

Pressure level

For example, recommended for 

HARD

Stone terraces made of paving 
stones or exposed aggregate con-
crete, asphalt, metal surfaces, gar-
den utensils (wheelbarrow, spade, 
etc.)

MEDIUM

Motorcar / motorcycle, brick sur-
faces, plastered walls, plastic furni-
ture

SOFT

Wooden surfaces, bicycles, sand 
stone surfaces, rattan furniture

MIX

Operation with detergent

13

EN