GIGABYTE GA H61M USB3 B3 rev 1 0 - Инструкция по эксплуатации - Страница 32

BIOS Setup

- 32 -

  ACPI Suspend Type 

Specifies the ACPI sleep state when the system enters suspend. 

S1(POS)   

 Enables  the  system  to  enter  the  ACPI  S1  (Power  on  Suspend)  sleep  state.  

In  S1  sleep  state,  the  system  appears  suspended  and  stays  in  a  low  power  mode. 

The system can be resumed at any time.

S3(STR)   

 Enables  the  system  to  enter  the ACPI  S3  (Suspend  to  RAM)  sleep  state  (default).  

In S3 sleep state, the system appears to be off and consumes less power than in the 

S1  state.  When  signaled  by  a  wake-up  device  or  event,  the  system  resumes  to  its 

working state exactly where it was left off.

  Soft-Off by PWR-BTTN

Configures the way to turn off the computer in MS-DOS mode using the power button. 

Instant-Off   

Press the power button and then the system will be turned off instantly. (Default)

Delay 4 Sec.   Press  and  hold  the  power  button  for  4  seconds  to  turn  off  the  system.  If  the  power 

button is pressed for less than 4 seconds, the system will enter suspend mode.

  PME Event Wake Up

Allows the system to be awakened from an ACPI sleep state by a wake-up signal from a PCI or PCIe de-

vice. Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead. 

(Default: Enabled)

  Power On by Ring 

Allows  the  system  to  be  awakened  from  an ACPI  sleep  state  by  a  wake-up  signal  from  a  modem  that 

supports wake-up function. (Default: Enabled)

  Resume by Alarm

Determines whether to power on the system at a desired time. (Default: Disabled)

If enabled, set the date and time as following: 

Date (of Month) Alarm: Turn on the system at a specific time on each day or on a specific day in a month. 

Time (hh: mm: ss) Alarm: Set the time at which the system will be powered on automatically. 

Note: When using this function, avoid inadequate shutdown from the operating system or removal of the 

AC power, or the settings may not be effective.

  HPET Support

 (Note)

Enables or disables High Precision Event Timer (HPET) for Windows 7/Vista operating system.

(Default: Enabled)

  HPET Mode

 (Note)

Allows  you  to  select  the  HPET  mode  for  your  Windows  7/Vista  operating  system.  Select 

32-bit  mode

when  you  install  32-bit  Windows  7/Vista;  select 

64-bit  mode

  when  you  install  64-bit  Windows  7/Vista. 

This item is configurable only when the 

HPET Support

 is set to 

Enabled

. (Default: 32-bit mode)

  Power On By Mouse

Allows the system to be turned on by a PS/2 mouse wake-up event. (Default: Disabled)

Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead. 

Double Click  Double click on left button on the PS/2 mouse to turn on the system.

  Power On By Keyboard

Allows the system to be turned on by a PS/2 keyboard wake-up event. (Default: Disabled)

Note: you need an ATX power supply providing at least 1A on the +5VSB lead. 

Password   

Set a password with 1~5 characters to turn on the system. 

Keyboard 98  Press POWER button on the Windows 98 keyboard to turn on the system.

(Note)  Supported on Windows 7/Vista operating system only.