VITEK VT-3966 B - Инструкция по эксплуатации - Страница 6

ENGLISH

6

37.  Additional battery compartment lid (reserve 

supply for memory support)

38.  Remote control SENSOR
39.  USB jack
0.  SD/MMC card jack

Remote control (Pic. 2)

.  STANDBY button
 

During operation press the STANDBY 
button. The cassette recorder will switch to 
the standby mode. The STANDBY indication 
will light up.

To return to normal playback press the 
STANDBY button once again.

2.   FUNC button
3.   BAND button
.   REPEAT/MONO ST button
5.   TIMER/SLEEP button
6.   SKIP TUNING 



 button

7.   PLAY/PAUSE button
8.   STOP button
9.   MUTE button
a.  Press the button to mute sound.
b.  Press the button again to cancel the mute 

mode.

0.  RANDOM button
.  SKIP TUNING 



 button

2.  VOLUME 

 button

3.  VOLUME 

 button

.  IR emitter
5.  Battery compartment lid

POWER CONNECTION
Line supply

Before connecting the appliance, make sure 
that your home electricity supply corresponds to 
the voltage specified on the appliance. 
.   To connect the appliance, insert one end of 

the power cord in the jack (35, pic. ) and 
the other one – in the socket. The STANDBY 
indication will light up.

2.  To switch on the appliance press the 

POWER button.

Note: Static electricity can lead to interferences 
in the operation of the appliance. In this case 
disconnect the appliance, and then connect 
again. If the problem does not disappear, apply 
to the service center.

Battery supply

.  Disconnect the cassette recorder.
2.  Open the main battery compartment lid 

(36, pic. ) on the rear of the appliance, by 
pressing two catches following the arrow.

3.  Open the additional battery compartment 

lid (37, pic.). Insert 3 UM-3/AA batteries 
(not supplied) in the battery compartment to 
support memory of the appliance. Close the 
battery compartment lid (37, pic. ). 
Insert 8 UM-/D batteries (not supplied) in 
the main battery compartment.

.  Close the battery compartment lid  

(36, pic. ).

USING THE REMOTE CONTROL

Insert 2 UM-/АAA batteries (not supplied) in 
the battery compartment of the remote control.
When using the remote control direct it to infra-
red SENSOR on the cassette recorder. Effective 
distance of the remote control is about 5 me-
ters, if it decreases very much, check the bat-
teries and replace them if necessary. 

Functions of the remote control buttons are 
similar to those on the cassette recorder. Some 
buttons perform two functions, depending on 
the mode selected: disc playback mode or radio 
mode. 
Do not expose the remote control to high tem-
perature and direct sunlight; it can influence the 
operation of the appliance.

Attention!

Battery leakage can lead to injuries and dam-
ages of the appliance. To avoid damages of 
batteries follow the instructions below:
-   Place the batteries properly, following the 

polarity marked inside the appliance.

-   Do not use old and new batteries or 

batteries of different types together.

-   Take the batteries out if you are not going to 

use the appliance for a long time.

TIME SET TING

You can set time when the cassette recorder is 
in the standby mode. 
.  Press the MEMORY/CLK-ADJ button once. 

Time indication will start flashing on the 
LCD display. Use the SKIP TUNING 



 or 



button to adjust hours. 

2.  Press the MEMORY/CLK-ADJ button once 

3966IM.indd   6

07.07.2008   15:40:48