Makita DJV182Z - Инструкция по эксплуатации - Страница 10

10

1. Insert the rip fence into the rectangular hole on the 

side of the base with the fence guide facing up. Insert 
the circular guide pin through either of the two holes 
on the fence guide. Screw the threaded knob onto the 
pin to secure the pin.

2. Now slide the rip fence to the desired cutting radius, 

and tighten the bolt to secure it in place. Then move 
the base all the way forward.

NOTE:

• Always use blades No. B-17, B-18, B-26 or B-27 when 

cutting circles or arcs.

Guide rail adapter set (optional 
accessory) (Fig. 26)

When cutting parallel and uniform width or cutting straight, 
the use of the guide rail and the guide rail adapter will 
assure the production of fast and clean cuts.
To install the guide rail adapter, insert the rule bar into the 
square hole of the base as far as it goes. Secure the bolt 
with the hex wrench securely.

 (Fig. 27)

Install the guide rail adapter on the rail of the guide rail. 
Insert the rule bar into the square hole of the guide rail 
adapter. Put the base to the side of the guide rail, and 
secure the bolt securely.

 (Fig. 28)

 CAUTION:

• Always use blades No. B-8, B-13, B-16, B-17 or 58 

when using the guide rail and the guide rail adapter.

MAINTENANCE

 CAUTION:

• Always be sure that the tool is switched off and the 

battery cartridge is removed before attempting to 
perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the 

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs, 
any other maintenance or adjustment should be 
performed by Makita Authorized Service Centers, always 
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended 

for use with your Makita tool specified in this manual. 
The use of any other accessories or attachments might 
present a risk of injury to persons. Only use accessory 
or attachment for its stated purpose.

If you need any assistance for more details regarding 
these accessories, ask your local Makita Service Center.
• Jig saw blades
• Hex  wrench  4
• Rip fence (guide rule) set
• Guide rail adapter set
• Guide rail set
• Anti-splintering device
• Cover plate
• Dust nozzle assy
• Makita genuine battery and charger

NOTE:

• Some items in the list may be included in the tool 

package as standard accessories. They may differ 
from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according 
to EN60745:

Model DJV142

Sound pressure level (L

pA

): 78 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Model DJV182

Sound pressure level (L

pA

): 77 dB (A)

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined 
according to EN60745:

Model DJV142

Work mode: cutting boards
Vibration emission (a

h,B

): 7.0 m/s

2

Uncertainty (K): 1.5 m/s

2

Work mode: cutting sheet metal
Vibration emission (a

h,M

): 4.0 m/s

2

Uncertainty (K): 1.5 m/s

2

Model DJV182

Work mode: cutting boards
Vibration emission (a

h,B

): 7.0 m/s

2

Uncertainty (K): 1.5 m/s

2

Work mode: cutting sheet metal
Vibration emission (a

h,M

): 3.5 m/s

2

Uncertainty (K): 1.5 m/s

2

ENG901-1

• The declared vibration emission value has been 

measured in accordance with the standard test method 
and may be used for comparing one tool with another.

• The declared vibration emission value may also be 

used in a preliminary assessment of exposure.

 WARNING:

• The vibration emission during actual use of the power 

tool can differ from the declared emission value 
depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the 

operator that are based on an estimation of exposure in 
the actual conditions of use (taking account of all parts 
of the operating cycle such as the times when the tool 
is switched off and when it is running idle in addition to 
the trigger time).