Bosch GST 90 E - Инструкция по эксплуатации - Страница 13

 English | 

13

Bosch Power Tools

1 619 P08 843 | (5.5.10)

f

Use suitable detectors to determine if utili-
ty lines are hidden in the work area or call 
the local utility company for assistance. 

Contact with electric lines can lead to fire 
and electric shock. Damaging a gas line can 
lead to explosion. Penetrating a water line 
causes property damage or may cause an 
electric shock.

f

Secure the workpiece. 

A workpiece clamped 

with clamping devices or in a vice is held 
more secure than by hand.

f

Keep your workplace clean. 

Blends of mate-

rials are particularly dangerous. Dust from 
light alloys can burn or explode.

f

Always wait until the machine has come to 
a complete stop before placing it down. 

The 

tool insert can jam and lead to loss of control 
over the power tool.

f

Never use the machine with a damaged ca-
ble. Do not touch the damaged cable and 
pull the mains plug when the cable is dam-
aged while working. 

Damaged cables in-

crease the risk of an electric shock.

f

Observe correct mains voltage! The voltage 
of the power source must agree with the 
voltage specified on the nameplate of the 
machine. Power tools marked with 230 V 
can also be operated with 220 V.

f

Check the tight seating of the saw blade. 

A 

loose saw blade can fall out and lead to inju-
ries.

f

When ejecting the saw blade, hold the ma-
chine in such a manner that no persons or 
animals can be injured by the ejected saw 
blade.

f

Dusts from materials such as lead-contain-
ing coatings, some wood types, minerals 
and metal can be harmful to one’s health 
and cause allergic reactions, lead to respi-
ratory infections and/or cancer.

 Materials 

containing asbestos may only be worked by 
specialists.
– Provide for good ventilation of the work-

ing place.

– It is recommended to wear a P2 filter-

class respirator.

Observe the relevant regulations in your 
country for the materials to be worked.

f

In extreme conditions, always use dust ex-
traction as far as possible. Blow out ventila-
tion slots frequently and install a residual 
current device (RCD). 

When working metals, 

conductive dust can settle in the interior of 
the power tool. The total insulation of the 
power tool can be impaired.

f

The contact protector attached to the cas-
ing prevents accidental touching of the saw 
blade during the working procedure and 
may not be removed.

f

Before sawing in wood, particle boards, 
building materials etc., check for foreign 
objects, such as nails, screws, etc. and re-
move them as required.

f

Plunge cuts may only be applied to soft ma-
terials, such as wood, gypsum board, etc.

f

The sliding shoe can prevent the surface 
from being scratched. The splinter guard 
can prevent fraying of the surface while 
sawing wood. Do not use the splinter guard 
for mitre cuts.

f

Adapt the settings of your power tool to the 
respective application. For example, reduce 
the stroke rate and orbital action when cut-
ting metal or for tight curved cuts.

Products sold in GB only

: Your product is fitted 

with an BS 1363/A approved electric plug with 
internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, 
it should be cut off and an appropriate plug fit-
ted in its place by an authorised customer serv-
ice agent. The replacement plug should have the 
same fuse rating as the original plug.
The severed plug must be disposed of to avoid a 
possible shock hazard and should never be in-
serted into a mains socket elsewhere.

Products sold in AUS and NZ only

: Use a resid-

ual current device (RCD) with a rated residual 
current of 30 mA or less.

OBJ_BUCH-1231-001.book  Page 13  Wednesday, May 5, 2010  11:59 AM