Neoclima NS-07 - Инструкция по эксплуатации - Страница 60



 Page 21



Indoor Unit

Installation 

Step 3: Drill wall hole for connective piping

1.

Determine the location of the wall hole based 

on the position of the mounting plate. Refer 

to 

Mounting Plate Dimensions. 

Wall

Indoor

Outdoor

m

m

7-

5

(0.2-0.275in)

Fig.3.2

MOUNTING PLATE DIMENSIONS

Different models have different mounting plates.
For the different customization requirements, the 
shape of the mounting plate may be slightly 
different. But the installation dimensions are the 
same for the same size of indoor unit. 
See Type A and Type B  for example:  

Correct orientation of Mounting Plate

2.

Using a 65mm (2.5in) or 90mm(3.54in)
(depending on models )core drill, drill a 
hole in the wall. Make sure that the hole
is drilled at a slight downward angle, so 
that the outdoor end of the hole is lower 
than the indoor end by about 5mm to 7mm 
(0.2-0.275in). This will ensure proper water 
drainage.    

3.

Place the protective wall cuff in the hole. This 

protects the edges of the hole and will help 

seal it when you finish the installation process.

 CAUTION

When drilling the wall hole, make sure to 

avoid wires, plumbing, and other sensitive 

components.

Type A

Type B

101mm (4in)

179mm (7.05in)

136mm (5.35in)

37mm (1.45in)

290mm (11.4in)

49mm (1.95in)

Right rear wall 
hole 65mm (2.5in)

Indoor unit outline

722mm (28.45in)

49mm (1.95in)

192mm (7.55in)

232mm (9.15in)

426mm (16.8in)

128mm (5.05in)

43mm (1.7in)

297mm (11.7in)

Left rear wall 
hole 65mm  (2.5in)

Left rear wall 
hole 65mm  (2.5in)

Left rear wall 
hole 65mm  (2.5in)

Right rear wall 
hole 65mm (2.5in)

Indoor unit outline

802mm (31.6in)

43mm (1.7in)

43mm (1.7in)

144mm (5.65in)

58mm (2.3in)

319mm (12.55in)

57mm (2.25in)

40mm (1.55in)

Right rear wall 
hole 65mm (2.5in)

Model C

Model B

Model A

965mm (38in)

138mm (5.45in)

34mm (1.35in)

Indoor unit outline

219mm (8.6in)

553mm (21.77in)

300mm (11.8in)

335mm (13.2in)

Left rear wall 
hole 65mm (2.5in)

Right rear wall 
hole 65mm (2.5in)

Model D

1080mm (42.5in)

53.5mm
(2.1in)

47mm (1.85in)

76mm(3in)

53.5mm (2.1in)

47mm (1.85in)

148.7mm
(5.85in)

151mm (5.95in)

174.3mm (6.85in)

Indoor unit outline

172mm (6.8in)

362mm (14.25in)

Left rear wall 
hole 90mm (3.54in)

Right rear wall 
hole 90mm (3.54in)

Model E

1259mm (49.55in)

Indoor unit outline

52mm (2.05in)

389mm (15.3in)

332mm (13.05in)

257mm (10.1in)

643.6mm (25.3in)

52mm (2.05in)

517.4mm (20.37in)

348.4mm (13.7in)

Φ

NOTE: 

When the gas side connective pipe is

    16mm(5/8in) or more, the wall hole should
be 90mm(3.54in).